Find experienced local carpenters in Frankston

I have a vertical aesthetic board that is floor to ceiling in height. it is impeding a sprinkler head. i need the board cut down in size by approx 35 cm. It is 2 meters wide . The board is attached with screw and can be taken down to cut

To prepare for the installation of 2 x skylights (1275 x 1275) in a kitchen, we need 2 x structural beams - securely braced/fitted. Structural carpenters or builders only please.

Looking for a carpenter/handyman – small storage room job We're looking for someone to help with a small walk-in storage cupboard conversion in Frankston. We can handle the small demolition and any electrical work it may involve. We need someone to: - Reframe/relocate a section of an internal non-load-bearing wall - Close off the existing doorway/opening - Create a new 820mm door opening in the new position - Supply/install the door jamb and hang the door - Leave everything square and ready for me to plaster Hoping this is a one-day job for someone experienced. Doesn't necessarily need to be a qualified carpenter. Happy to consider an experienced handyman who has done this type of work before. Please message me with your availability and rough price. (floorplan below - new door to go on new wall in entryway.)

Fix/replace a wood panel which was water damaged near sliding door

Remove old wooden timber frame that has rotten and replace with new. Please supply the timber I don’t have any. Does not require being painted over as shutters will be going over the top. See photos

I have a new 2340 x 820 x 40 door that requires sanding,staining and fitting. I will provide deadbolt and handle lock assembly, stain and existing hinges should be ok to reuse.

We have a pergola roof around 20 sqm where the old fiberglass roofing sheets need complete removal and stacked neatly on site for our own skip bin collection. One rotten timber beam approximately 3 metres long also needs to be removed and replaced. Please supply and install new polycarbonate corrugated roofing sheets with all flashing and waterproof sealing.

Cabinet maker to make draws

Looking for someone with cabinet making experience to build draws into existing cabinetry

need to remove 2 sinks and joinery seal off/remove piping

I purchased a bathroom cabinet from IKEA but I don't have any anchors or mounting brackets. I need a person to mount this cabinet permanently on my bathroom wall. The bathroom wall is tiled so will need a drill. I don't have any bolts or anchors to mount it with so the person will need to use their own or source required parts from Bunnings. The doors and shelves will be fitted by myself once the cabinet is mounted.

Installation of kitchen cabinet come with a saw

Description: Looking for an experienced handyman or cabinet maker to replace: 1. Laundry internal shelf • Located inside lower laundry cabinetry. • White melamine board. • Existing shelf to be removed and replaced with new board cut to size. • Must match existing finish as closely as possible. • Securely installed and level. 2. Cabinet panel / door • One white panel (or cabinet door) requires replacement. • Must colour-match existing white cabinetry. • Supply, cut and install. • Ensure alignment and clean finish. Photos attached for reference. Requirements: • Supply all materials. • Remove and dispose of damaged pieces. • Professional finish (no visible gaps, rough edges or poor alignment). • Experience with cabinetry preferred.

Just after quote and replacing and repair rotten wood on side roof of house.

Carpenter to provide detailed written quotes to repair damage to aa non-structural wall including full scope of works and proposed materials to be used etc..

Carpenter to repair damage to non-structural wall.

I’m looking for an experienced cabinet installer/carpenter to install a full set of base (lower) kitchen cabinets in my home. The space has been renovated: walls are patched/drywalled, plumbing rough-in is complete for the sink, and the subfloor is exposed timber. 600mm drawer 600mm drawer 600mm sink drawer 600mm dishwasher (The 2400mm bench top goes along this). Need to add support brackets to support bench top along here. The drawer panels need to be swapped out as well as one of them is gloss white instead of antique white.

Please see picture for plan. Need the kitchen assembled and installed. Kitchen by blue star.

Looking to have a custom made foldable/compactable lightweight bar on wheels for events. Need it completed by 21/2 Willing to offer $900 to a cabinet maker who could complete this project well. Want to use MDF as its lightweight. Total Size: H1980mm x W1300mm x D600mm, Table size: H950mm x W1300mm x D600mm, Height from the table to the roof: 900mm.

Need two support braces attached to upright posts attached back towards the house for a shade sail. Need two 3m treated pine lengths 90 x 35/45 (please supply) and a nail gun preferably.