Find a reliable appliance technician in Miranda NSW

disconnect cook top come back second time to reconnect warranty replacement

disconnect cook top warranty team will take away and bring back reconnect once replacement arrives on another day.

REPLACEMENT OF MOTOR OF DYSON DC 19 VACCUM CLEANER

I'm looking for a qualified/certified gas fitter/plumber/electrician to disconnect and remove existing kitchen appliances and install/connect the following new appliances - Westinghouse 60cm Freestanding Dishwasher WSF6602XC Westinghouse 60cm 4-burner Gas Cooktop WHG648SC Westinghouse 60cm under bench Electric Oven WVE6314SD

Need new rangehood installed to new kitchen cupboard. Refer to photo of kitchen

BBQ not igniting properly

We have a beefeater BBQ that is not igniting properly

Looking for a handyman or plumber to install a dishwasher in my kitchen. It's a new installation. The dishwasher cavity is 1.5 metres away from the sink plumbing and the power point. Requirements: 1) Cabinetry: Might need to drill holes through the intermediate cupboards to route the hoses and power cord from the cavity to under the sink. There is an option to put them beneath the kitchen cabinets though. 2) Plumbing Connection: Connect the dishwasher to the cold water supply and the sink's sewer/waste pipe (1.5m away). 3) Electrical: Route the power cord to the existing power point located underneath the sink. 4) Setup: Position, level, and test the dishwasher to ensure there are no leaks and it runs properly. Notes: It might need a 2m or 2.5m extended dishwasher hose kit (inlet and drain hose extension), so please take them just in case.

our washer/ dryer is giving an AE error and the dryer sounds like it’s about to explode! it’s an LG

My washing machine had been stuck on flashing pause for nearly a week now and i have tried resetting, emptying the plug and none of it seems to work unless i am doing it wrong, another set of eyes could be helpful and hopefully get my washing machine up and running again! its a fisher and paykel 8.5kg washing machine for reference

Need a carpenter or handyman to convert a 62 cm end kitchen cabinet into a dishwasher cavity. The cabinet is under a stone benchtop, so you will need to install structural wall brackets or timber wall cleats to fully support the stone top before the cabinet carcass can be safely removed.

I have a manual churro machine with a cutter attachment. One of the screws that holds the spring/cutter assembly no longer stays secure because the threaded mounting point appears to be worn or stripped. Looking for someone with mechanical repair experience who can inspect and repair it, possibly by re-threading, installing a thread insert, or another suitable fix. Ideally looking for a durable repair rather than a temporary fix.

Dishwasher not completing cycle & making noise.

Looking for someone experienced with natural gas burners/appliances to inspect and adjust the flame on my outdoor burner/heater setup. Current issue: * Flame output is too low * Gas connection is working but may need valve/regulator adjustment or burner servicing Need someone who can: * inspect the gas valve assembly * adjust flame/gas flow safely * clean/check burner components * troubleshoot low flame issues Please only apply if you have experience working with natural gas appliances and fittings. I’ve attached photos of the gas valve assembly.

LG fridge stopped freezing & cooling two days before total fail to cool or freeze. Food in freezer was all thawed out. Lights work, Fans seem to work, No compressor sound. Clicking sound coming from PCB area when turning on power at mains. Turned off for 5 mins to attempt reset but no success. Red LED flashing on PCB - 3 flashes. Brand LG, Model: GT-422WDC. Top mount. Linear inverter compressor.

Hello, I’m contacting you regarding a commercial ice machine that requires diagnosis and repair. Machine details: Brand: Manitowoc Model: UG050A-251Z Issue: The machine powers on and starts making ice normally, but after a short period it shuts itself off. It will only run again if manually restarted. A previous technician inspected the unit and mentioned that the issue may be related to the control board (timing card), or possibly a sensor/bin control issue, but no parts were replaced and the problem remains unresolved. I would like a proper diagnosis and repair, and would appreciate if you could: Confirm the fault Advise if the control board needs replacement Provide an estimated cost (parts + labor) Let me know your availability and charges Please let me know if you need any additional information.

Lawnmower , located in Miranda 2228

Timber 75x200 supply install

Change door gasket on this kogan washing machine

Our dishwasher is faulting with flood alarms and also it’s making a funny sound with the pump.