Find a reliable appliance technician in South Adelaide

Hi there, I would like to book a repair service for my Euro Appliances top loader washing machine (Model: ETL7KWH). It is in good visual condition, but it has developed two specific issues: 1. Soap Powder Patches: It leaves noticeable white patches of undissolved soap powder on the clothes after the cleaning cycle is finished. 2. Spinning Noise: It makes an unusual noise whenever it is spinning. Could you please send a mechanic to inspect the agitator, water valves, and suspension/gaskets to figure out what is wrong and fix it? Let me know your next available times and pricing.

Hair straightener only likes to work in a certain position not sure if it’s a wire fault

Original oven was 70cm wide. New oven is 60cm wide. I need 5cm gap either side packed to match cabinets.

Remove & replace a rangehood

Site facts ========== + Smeg FS61XNG8 60 cm freestanding cooker, natural gas, ~2014 (previous owner). Gas inlet at the rear, right side; exact height to be confirmed when the cooker is pulled out. + The cooker is boxed in: a cabinet on the left (no easy way to use that), the dishwasher on the right ( The gap behind is 30–50 mm) so not possible to use. + The wall behind the oven is the external wall: double brick, 240 mm thick, untiled below bench height. The render behind the cooker is already damaged. + Current supply: tees off below a Rinnai Infinity water heater mounted outside on the same wall, directly behind the cooker. It runs down the outside wall (copper, then an older white-painted section with screwed fittings) and enters the wall at ground level. Inside, there is a valve about 50 mm above the floor at rear left, and a braided hose runs under the cooker. There is no restraint chain, and the cooker can’t be pulled out. + New flooring is going in on 9 Nov. Requirements ========== + to be done before 5/11/26. time date - you decide +Fully compliant with AS/NZS 5601.1 and the Smeg instructions, with an eCoC issued. +I must be able to disconnect and reconnect the cooker myself, without tools, to pull it out for cleaning and flooring (MOST BE quick-connect device, cl. 5.9.6(b)). +The cooker goes back to its current position against the wall, no more than 10 mm further forward than it is now. + No redundant gas pipework left live. + One visit, fixed price. In your quote, please describe your proposed route and method; confirm requirements 2 and 3 in writing; Scope: cooker branch only. If you see an issue with the water heater, please tell me and quote it separately.

Hi, I need a licensed South Australian gas plumber for a quick two-part job to accommodate a new vinyl floor installation in my kitchen. Visit 1 (Before flooring): 26/10/26. Disconnect a freestanding gas cooker (Smeg FS61XNG8). It is currently connected via a flexible hose and a manual shut-off valve, so it should be a very straightforward disconnection. Visit 2 (After flooring): 29/10 -afternoon. Return once the floor is finished (likely [Insert number of days] days later) to safely reconnect the oven, test for leaks, and level the feet on the new floor. Requirements: You must hold a valid SA gas fitting license and provide a Certificate of Compliance upon completion of the reconnection. Please ensure your offer covers the total cost for both visits. Let me know your availability for the disconnect!

Hi, I’m looking for someone experienced in washing machine repairs to diagnose and fix my washing machine. The machine keeps displaying an E03 error code and won’t drain or complete a wash cycle properly. What I’ve already checked: * Drained the water manually. * Removed and cleaned the drain filter. * Checked the pump impeller, which appears to spin freely. * Checked the drain hose for kinks or blockages. * Unplugged and restarted the machine. Current problem: * The washing machine makes a brief humming noise, stops, then repeats. * Water is not pumping out through the drain hose. * When I manually opened the drain filter, a large amount of water came rushing out. * Clothes are left soaking wet because the machine won’t drain or spin properly. I suspect the drain pump may be faulty, but need someone to diagnose the issue and repair it. Ideally looking for someone who can attend as soon as possible. Please provide a quote for diagnosis and repair, including any replacement parts if required. Thanks!

Bosch oven electrical repair The oven is not working. I removed the front panel and noticed some burnt/damaged wires inside. I’m looking for a qualified electrician/technician to inspect the oven, identify the cause, and repair or replace the damaged wiring and any faulty components as required.

Power supply has failed -- no lights showing on remote control

Pinball machine has sat idle for 18 months turns on but nothing comes up on screen so it must be something to do with the computer box inside

Looking for someone to help install a dishwasher in our kitchen. We don’t currently have a spot for one, so we’ll need the inside of one of the cabinets removed/modified to make room for it. We’ll also need the plumbing run from the sink over to the dishwasher, and a power point installed for it. It’s next to a corner cabinet, and I’m hoping we can keep some access to that cupboard by moving the existing corner door to the right-hand side instead. We already have the dishwasher and it’s 60cm wide. Happy to send photos/measurements if needed. Bosch Series 2 Freestanding Dishwasher Silver Inox SMS24AI01A

I would like my Weber Q cleaned

install customer supplied commercial dishwasher at cafe and change hot duo valve , transport removed dishwasher to customers home and swap out with existing unit, dump old dishwasher

Dishwasher not working, water in the bottom… see photos

Brand new rower, belt / pulley screw needs to be put in that holds in place.

Pullout old dishwasher and fit new one. Easy access Bring trolly to put old one on footpath

Cabinetry is already done, I need someone to take out the old range hood and fit the new range hood which I have purchased

Just got new washing machine but they couldn't install because the end of the hose is too chunky to fit with the current tap configuration. The valve needs to be rotated so that it can fit. Washing machine not in position to make access easier so will need to be repositioned about ten metres. I have a little trolley to assist with this.

Pick up hotplate from Harvey Norman, Marion Warehouse: 20–22 Butler Boulevard, Adelaide Airport, SA 5950. Model: WHC943BD WEST/HOUSE 90CM 4 ZONE CERAMIC COOKTOP. Removal of old hotplate and installation of new one at Clarendon home.

Hi Harry :) I found your profile and saw you’re experienced with treadmill setup and levelling. I’m hoping you may be able to help me with mine. I’ve had ongoing issues where I suspect the treadmill is still slightly off level, and it feels like I’m walking on an incline. It’s been affecting my comfort and gait, so I’d really like it checked properly. I’m looking for someone who can assess and adjust it so it is as close to 100% level as possible — side to side and front to back. Please let me know if this is something you can assist with. Thank you so much! 😊 Cheers, Emily