Find a reliable appliance technician in Mount Gravatt East

Dishwasher will not turn on after not being used for 3 weeks. Drain and water connections have been checked and are ok. Power connection ok. Door closes ok. Seems like a fault with the electronics or motor. Looking at someone to initially check and provide advice on what to repair. Depending on the outcome would need a further task to repair.

The rangehood is blowing the air out instead of sucking the air in. Looks like the rangehood isn't properly set up, will you be able to fix it tomorrow if possible. Let me know Rohit

In relation to the jobs to be done: 1. Dryer to be hung: see attached photos of board, bracket, screws, instructions and dryer - 2. Downstairs door stop: see attached - it doesn't line up / work - email 2 3. Upstairs door stop: see attached: it is too short and has put a hole in the wall - 4. Linen cupboard hooks are broken (both doors) and it doesn't latch properly. 5. Bathroom towel rack to be installed: we will need to source a matching rail (see attached).

Hi, i need someone to install 7 air-cons in my house. - Due date: Flexible

I require my existing ceramic stovetop to be replaced by a new one the same size supplied by myself. Located in Mount Gravatt East.

Glass plate for the electric cooktop needs to be replaced. It ideally wouldn’t be a job longer than 30 minutes for an experienced person. - Due date: Flexible

The kitchen renovation is almost done, the benchtops will be installed on Friday morning 8th December. I am currently looking for a plumber to help connect two tap mixers and a dishwasher. You must be available on Friday afternoon or later to complete this connection as I will be away on weekends. The price offered here is for reference only, coz I have no idea about the current market price. If you are interested, please quote with labor and materials(S&P trap combination with necessary PVC connection) included. I will update the quote once confirmed, thank you! - Due date: Needs to be done on Friday, 8 December 2023

I have purchased a dishwasher but now need to re-build / modify my cupboards to fit this in. - Due date: Flexible

Flashing red button, and losing heat after a minute of being on - Due date: Before Monday, 4 December 2023

Install 900 cm canopy rangehood , it has an offboard motor that needs to be hooked up in the roof cavity. Product: SIRIUS 900MM BLACK CANOPY SIRIUS SEM SILENT MOTOR 1 INTERNAL - Due date: Before Friday, 24 November 2023

Need a dishwasher supplied and install at a property. - Due date: Flexible

Install Whirlybird on roof tiles. Its a 2 Storey house. The installer must be qbbc register and insured to do the job at task. Price above is for installation only. Please suggest which Whirlybird we should buy. Thank you - Due date: Flexible

My renegade R3000-9 pressure washer starts easily, runs well but stops 5-10 seconds later. It does this about 10 times before it will then run properly. After stopping it won't start again immediately, but have to wait 1-2 minutes between attempts. I'd like someone to diagnose and fix the fault. - Due date: Flexible

Stove top supply and replacement/install - Due date: Needs to be done on Thursday, 7 September 2023

Can smell gas when connected to 8.5kg LPG gas bottles, need someone to supply and install a replacement regulator, then check for any more leaks. - Due date: Needs to be done on Sunday, 20 August 2023

Looking for someone to help install a washing machine in a new house, unsure of how the old owners connected it - attached photos show the washing machine and where we are trying to connect it into. Ideally completed today Friday 21/7 in the afternoon or evening but can also be Saturday 22/7 - Due date: Before Saturday, 22 July 2023

Our Bosch dishwasher is intermittently not draining, leaving water in the bottom of it.

I need a dryer mounted up on a wall that already has a bracket - Due date: Flexible

Haier HDY-M40 tumble dryer has stopped tumbling. This will require a new replacement Haier capacitor HDY60 & 60M - Due date: Flexible

I have a Ender 5 Plus that I bought brand new, assembled it, but can't seem to get it accurately leveled. Installed firmware is Ver 1.70.3 BL I've followed many YouTube tutorials and read many Reddit threads, but I have been unsuccessful in this pursuit. I'd preferably like to offer this task, to someone that already has an Ender 5 Plus and has experienced similar issues. I have attached the most recent values, of how leveled it is. It's definitely an improvement from where I started, but I can nolonger invest time to troubleshooting this problem.