Hire trusted appliance installation services in North West Perth

Install new outdoors rangehood. RANGEHOOD PLAN ✔ Crossray 90 cm alfresco BBQ hood https://www.harveynorman.com.au ✔ Mount 750–850 mm above BBQ ✔ Duct vertically then out right-hand side wall (Installation method) ✔ 150 mm rigid metal duct (aluminium / galvanised) https://www.fansonline.com.au ✔ 150 mm weatherproof external wall vent (with flap + mesh) https://www.fansonline.com.au INSTALLATION INSTRUCTIONS – BBQ RANGEHOOD EXTERNAL DUCT 1. Hood Mounting Height Fix the rangehood 750–900 mm above BBQ cooking surface. Ensure hood is level and anchored into studs or brick. 2. Ducting Materials Use 150 mm rigid galvanized steel or semi-rigid aluminium duct. Avoid thin foil or flexible plastic duct — poor airflow and fire risk. 3. Duct Path Run duct vertically up from the hood outlet, then directly to the external side wall. Minimise turns — one 45° or 90° bend max if needed. Keep total duct run as short and straight as possible. 4. Wall Penetration Core-drill or cut a 160–170 mm hole through brick/wall. Angle duct slightly downward toward outside to prevent condensation running back. 5. External Vent Installation Select a 150 mm external vent (e.g., stainless or weatherproof hood). Mount vent clear of other pipes or fixtures and at least: 600 mm from doors/windows 300 mm below eaves Seal all around the vent with exterior silicone to weatherproof. 6. Backdraft & Mesh Ensure the external vent has backdraft protection (gravity flap or mesh). Check mesh covers openings to stop insects/rodents. 7. Sealing & Insulation Use HVAC aluminium tape on all duct joints. No ducting should vent into ceiling cavities. 8. Power & Safety Confirm the rangehood is powered with a dedicated, weatherproof outlet or hard-wired by a licensed electrician. Test airflow after installation — smoke/test paper should move out of vent cleanly.

Full Install rangehood properly

Simpson EZISet Front Load Washing Machine rubber seal requiring replacement. Have the replacement. Need to be completed before Sunday 15th. Only experienced people who have completed this before please- No DIY This is for a rental bond. Must bring own tools.

Old Rangehood removed new one need to drilled into place

Replacing existing unit that’s been removed just need drilled in

I have a new Illusion fire place thats been put in the wall. It's not connected to gas, and the new flute hasn't been installed/connected.

Supply and fit 1 x new replacement Chef CRC612SB or similar 60cm stainless steel canopy rangehood and remove/dispose of old rangehood (may require minor patching/painting

Install new oven and undermount rangehood and removed both existing

Approximately 50 50 msq laser lite polycarbonate installed

Repair range hood switch, require ceiling fan remotes and replace led light in bar fridge

Oven and grill standard 600mm replacement. Disconnect and remove old oven/grill and install new one

I have a new Westinghouse WRR604SB 60cm slide-out rangehood. Old unit is already loosened (filter and screws removed) but stuck on cabinet edge. Power point is available (plug-in, no electrical work needed). Need removal of old unit and installation of new one. Location: Balcatta.

Supply and installation of a power point to the front door area Single story house and tiled roof

Remove old clothes line and install new one. They are similar the new one is just higher as its adjustable. New one is already at my house.

Have moved into a new property, need the washing machine and dishwasher connected to the plumbing.

Removal existing range hood along with cabinets and installation of a new range hood and installation of new one (free standing) before Christmas

To screw in smoke alarms to the ceiling, smoke alarms will be provided

Looking for someone to install a wall mounted clothes line in my backyard. Comes with all parts ready to go, the brand is Outback Clothesline.

Install 2x baby gates Connect up fridge water - connection already there , just need to hook up. Will take around 5mins Move bars for monkey bars abit higher - will take around 15mins Main task is to install the baby gate