Find professional window and door services in North West Perth

Looking for an experienced spray painter to repaint my front entry door and garage door in Dulux Domino Scope: - Preparation and sanding - Masking/protection of surrounding areas - Spray painting onsite - Front timber entry door - Double garage door - Exterior-grade products only - Smooth modern finish required I will likely remove/replace front door hardware separately. Please provide: - examples/photos of previous work - whether paint is supplied or additional and any cost difference if you were to source it as opposed to me - estimated timeframe for completion - total quote Looking for someone experienced with exterior doors and garage doors who can achieve a clean, modern finish.

I had to remove my roller door and now I can’t remember how to re-install and set up correctly.

I’m installing 20x garage doors at 3200 high x 6000 wide. Need labour to lift panels up a 6 step ladder and screw hinges. Tools provided.

Screen door repaired. Please message/Comment with your quotes. Been two years and only now has my dogs decided to have a go at it. This needs to be done before the 15th. Just standard mesh nothing special about it

Few random things to be fixed around the place: 1. Pantry door handle is starting to fall off. The hole for the screw is stripped, otherwise I'd just tighten the screw. Want this fixed so handle is firm and not going to fall off. 2. Cupboard under sink, door is hanging slightly askew on the corner hinges. Want this hanging straight 3. Shower screen block for the pivot hinge is broken. Have repaired with Araldite but door isn't hanging straight. Want this block replaced and door to open and close properly.

Need door handle fixed

Cut glass door to install cat door

Had all my internal doors repainted. The new handles don’t fit the current hole (too small) on the doors. Need 12 handles installed

Need help fixing the cap of the bottom of the garage door which has fallen off. Would need the right screws and drill for metal

One roller on sliding door is jammed - electric saw will be required to cut through screws. Require 2 x rollers replaced on sliding door (there is a Bunnings on my street, I’ll grab the right size once confirmed) and flywire replaced on 3 x frames - I have the new flywire and tubing ready here to use. Job in Joondanna 6060

Hi I need a door frame supplied and installed for a house in Dianellla. The door supplied for hanging is 81.5cm x 202cm (hinged door). Quote to include frame, plastering at the top, hang existing door and removal of all rubbish. Space for door and frame is 91.5cm (w) x 242.5cm (h, ground to ceiling).

I have a door that needs a weatherproof seal put on the bottom. It may need a little bit shearing off

I trimmed the edge of a door to shorten however the cut is wonky and I need help smoothing or levelling the edge.

Looking for a handyman/carpenter to fit a new door to an old door frame. All materials to be purchased by me need someone with the tools and know-how to install. It is an older house, built in 1978, so the door frame is not exact (see measurements). It will therefore need to be trimmed and planed a fair amount, hence we will be using a Solid Timber Pine Core (STPC) door, which will also need to use wide throw hinges (happy to re-use existing hardware) so the door can swing past the inside wall, + fitment of door hardware handle + latch assembly. Happy for you to come and take a look at the job before undertaking work and purchasing materials. The door will also be very heavy, so I'm more than happy to help with assisting/lifting. Measurements: Door Frame Height: (slight decline left to right) Left = 1990mm Centre = 1985mm Right = 1983mm Width: Top = 815mm Middle = 815mm Bottom = 810mm Depth: 40mm

I have a new internal door that needs to be cut to size and hung. The door will need trimming to fit the existing frame, hinges installed (or transferred from old door), and door hung so it opens and closes properly. Also need hole drilled for handle. Looking for someone experienced with carpentry or door installation. Please bring necessary tools.

Door handle is loose , you will need to bring your own tools … not an expert in this but maybe some screw drivers to tighten it ? Please make sure before requesting an offer you stick to the time and date that we have arranged . If you feel you’re inadequate and have poor organisational skills please do not accept this task. I don’t have time for time wasters !

The door had moved slightly so I can’t close it - it needs slightly realigned maybe 2mm ?

I need a single garage roller door removed (including all side roller panels) and taken away. Located in Trigg.

Need a new flyscreen fitted to our sliding screen door. (Current one torn) Size is approx 200 x 120. It’s a sliding stacker door so mesh needs to match mesh on other door. See photos. Thank you :)

I need a dog door removed from a low light window- the entire pane of glass with the dog door in it, and the original pane of glass put back in (I have that). It’s a rental and I’m moving out so I have to return it to how it was. The job needs to be done between us moving out on the 13th would prefer it done the 17th at the absolute latest. You’ll need your own tools and supplies to put the other windows pane in. It’s small, the door was for Jack Russell’s.