Find professional electric boiler installation & repairs in West London

In my electric boiler, there is a leakage whixh seems coming from the immersion heater that needs to be fixed

Looking for a certified boiler engineer to replace the burner seal on my boiler. I have the spare part already.

Heating and hot water not working

I have a boiler with 2 connecting pipes going into it. One of the pipes is leaking so just needs attention and tightening.

I need my boiler to be checked as it is loosing pressure often. I am only paying a small amount as I don’t want it to be fixed exactly, I need you to tell me how difficult it is to fix before hand.

boiler fan won’t start up, have part needs installed

I need to cover the pipes of my boiler , please send me quote

Intercom isn’t working. Could be wiring. Also instal a thermostat onto boiler. Must supply a cheap thermostat

Water was coming out of the boiler

Replace boiler control/thermostat with new model

Job Description: Following the recent installation of a new boiler, the flue penetration and surrounding wall area have been left unfinished. The opening around the flue is uneven, with exposed substrate, gaps, and patchy filler visible. The area requires making good to a neat, paint-ready finish that blends seamlessly with the surrounding wall. Scope of Works: • Inspect the area around the boiler flue and assess surface condition • Prepare surfaces by removing loose material, excess filler, and debris • Sand uneven areas to level the surface • Fill and smooth gaps around the flue collar to create a clean, flush finish • Apply plaster or suitable filler as required to achieve a uniform wall surface • Allow adequate drying time and carry out final sanding • Prime repaired area if needed • Paint to match existing wall colour and finish Materials Likely Required: • Filler and/or plaster (suitable for internal wall repairs) • Sandpaper or sanding block • Primer / mist coat • White emulsion paint (or colour to match existing wall) • Caulking (if required for neat finish around flue edge) Finish Required: A tidy, professional finish with no visible gaps, rough edges, or patch marks. The repaired area should blend in with the existing wall and look as though the flue installation was originally finished to a high standard. Additional Notes: • Boiler and flue are already installed and operational • No changes required to the boiler or flue itself • This is purely cosmetic / making good works

Boiler service to be done. Flexible on day and time

Combi boiler repair and servicing. It is taking too much time for heating.

Hi, I am looking to box in a boiler at my home in Egham (TW20 8TH). The job is slightly specific as I need an "L-shaped" enclosure rather than a full cupboard. The requirements are as follows: Dimensions: Approximately 120cm (H) x 60cm (W) x 30cm (D). Configuration: Front door panel and a Left-hand side panel. Accessibility: The Right-hand side must remain open to allow for existing pipework to run to the wall and for ventilation/access. Could you please let me know if you can assist with this? I would appreciate a rough estimate for labour and materials, and an idea of when you might be available to carry out the work. Attached is a photo of the boiler and the surrounding pipework if that helps with the quote. 2) I also need a piece of white coloured word cut to size and place onto top of a drawer unit to cover the brick work behind.Approx 41"L, 0.5"T, 5.5"W. Photo also attached.

Boiler errror 133 or not working radiatorand water

Vaillant EcoTec Plus. Flashing 0.0 and clicking. Filling loop at 1.3

Got a combi boiler with no hot water

Looking for gas certified plumber to replace leaking valve under the boiler. We already have the replacement part

Need my boiler repressurising. It's very simple and just requires two taps to be opened and closed. Does not need a plumber but can be done by anyone. The issue is the person in the house is unable to access it as you need to stand on a ladder to reach it. Ladder is provided.

Currently having some work done on my kitchen and I’m looking for a plumber/hesting engineer to remove the old bulky boiler filter and replace / possible slightly reposition with a smaller more compact filter.