Book a professional blind repair service in Sydney Northern Beaches

Blind has fallen off The rotator is stuck and brackets are coming off from the wall.

Looking for someone to install 1 x kitchen blind 1 x bathroom blind I have removed the one of the old blinds, the bathroom still needs to be taken down Blinds are standard, bought from spotlight, easy to install I just don’t have the correct drill.

The blind does not slide open or close properly, plus 8 Slats bunch up together and will not separate when opening and shutting the blind.

Install 4 x venetian blinds to windows

Install 2 roller blinds (1200 and 2400 wide) into concrete wall with gyprock. Current blinds to be removed. I will dispose of them.

Install 2 blinds on concrete wall. Blinds are ready. Offer me

Purchased 5 minute blinds. Need handyman with cordless drill, Phillips head drill bit (PH2 size), A pencil, 3mm drill bit to install them. x1 sheer and x1 roller blinds. Install details are on their website. going into giprock, however it is giprock and then metal about 5mm in so you will need a metal drill piece and also 10mm wall anchors. Should take 45 mins max. We have done one already but it’s proved a bit difficult, if possible might see if you can also reposition the one we put up as it’s not the best job. Ideally someone with a lot of experience in this!

I need someone to install roller blinds in a study.

Looking for an experienced handyman to install one VELUX Solar Powered Blind (Model: FSCC/FSCD/FSCH/FSCF series) on an existing VELUX skylight in a bedroom. ​Details: ​Blind Type: Solar-powered (no wiring required). ​Location: Installation is on a skylight in a standard-height ceiling. ​What’s provided: I have the blind kit and the installation manual (BM-IA007-XX). ​Requirements: You must have your own tall ladder and experience with VELUX products to ensure a clean install without damaging the skylight frame.

The job is installing new ceiling tracks and also hanging into existing tracks. 2 large windows >> Measure, drill, install 2x ceiling mounted track and attach existing sheer blinds. 5m and 2.5m lengths Another large window >> Place 2 roller blinds into existing brackets & hang 1 set of sheer curtains into existing track. 3.5m height. >> Smaller window - reinstall roller blinds brackets to wall and add the roller blind Ceiling is 3.5m tall in 2 work zones so you will need high ladder Curtain installation experience is preferred!

Installing blinds above windows on wall Measuring Levelling Functioning

There are 4x blinds that need to ne installed above 2x pairs of windows. Skilled person to: Measure & marked out on wall above window. Level, Drilled into place Installed to function. Tools available if needed; There's a ladder, a level, a drill available, but will need a skilled someone to be creative, as each blind bracket will need to be halved to cover 2x windows (2nd photo). May possibly be up to 2 hours work. Budget is set at $150

I need two roller blinds and three Roman blinds hung. Drilling is into wood as well as masonry wall.

Replace the cord that draws the vertical blinds open and shut and replace the chain which tilts the louvres

Plastic chain broken, can’t open and close. It’s in a bedroom

Plastic chain has broken on vertical blind and I can’t open and clos

I have 4 electric blinds in my living room (2 sheer and blackout), which haven’t been working since they were reinstalled after some renovations. Brand: TUBE 35-RTT 6/28 EA The issue is that only 1 blind is working like it should. The other 3 are either not going down to the floor or not working. I can confirm that all the motors are working as I am able to jog all the motors by isolating each motor blind to each the remote. I can get each moving but I can’t reset the upper or lower limit or directions so they don’t all go all the way down.

I need 2x blinds fixed in my home property One is a roller blind that’s fallen off the bracket (I have the blind) The other is a string pull blind and a few strings have broken

3 blinds install drilling into brick

We need someone who has a drill, with all the bits to drill into metal to hang 2 small blinds. They are brand new and come with everything to hang them. We will buy the screws that can go into metal, but need you to bring the drill bit that enables you to drill into a Phillips screw please.