Find a fence installation professional in Brisbane

Wood fence replacement including gate. Same look as existing. Price to be discussed in offer.

Replace steel mesh boundary fence with a new timber one. Happy to retain and use existing steel posts, which are straight and in line. May require additional (matching) steel posts in middle of the (~2.4m) span between existing, to provide extra strength. Fence will be 10m long, timber palings, small space between palings (i.e. not overlapping/solid). One sleeper at bottom to retain the neighbour's garden bed.

Approx 15m Butted Treated Pine Fencing 1.8m Height Hardwood Posts Treated Pine Rails Treated Pine Palings Supply, Installation and Rubbish Removal

Looking for a handyman to build a pet fence and gates for a small areas beside our house. We have a gate that also needs to be repaired.

Need to have two existing pool gate hinges removed and two new ones installed and appropriately tensioned. Should be only about 20 minutes work

Had a treelopper in last week and a few of the lattice timber extension have snapped off and been damaged beyond repair. Approximately 10m length of fence extensions need to be replaced and repaired. Please include in quote the repair/replacement on 2m of treated pine decking and an extra hour of labour to help refit an external roller door.

Wrought iron dual leaf swing D/way gates - clean/clear position. Person needs to establish cement base to be pinned to cement driveway & boundary pillar footings. Blacksmith is providing gates (each leaf is approx 350kg &1.8m wide) and poles and pillar/pole tabs. Installer to supply & fit all items necessary for installation eg motors, battery, etc.. Power is close. Suggest potential installers must be experienced & knowledgeable and visit residence.

We are looking to get a sliding gate built and installed at our house in Ashgrove. Gate specifications: Total width of driveway = 4.6m Height of desired gate = 1.8m (from ground to tip of the arrow castings on fence) Require: Motorised sliding gate + swinging pedestrian gate. Pedestrian gate to be on left hand side of the gate. The sliding gate needs to slide on the outside of the fence to the right. We have desired gate designs and fabrication price for the gate from oxworks. Need quote for motor + rest of job. Max budget $7500 including gate cost which was quoted at $2,424.24. Also happy to hear other build quotes if applicable. Would like the job done asap

Replacing a Timber gate The rough size is 122 x 92 mm.

Need to replace approximately 8 metres of fence between our house and the neighbours house. Need new fence palings as well as new fence rails. Posts are okay.

Damaged the fence and need just the one piece replaced. It’s a very simple straightforward job. Pls place offers

Old rotting boundary fence which happens to be pool fence required immediate build (1.8 m high) happy with timber or any other recommended solution

Removal and replacement of approximately 5 metres of fencing at a height of 800mm, Around 36 palings. No painting required

Need a guy to supply and install a aluminium composite panel for a shopfront awning. the dimension is about 2.8m by 1.7m

Remove concrete step. Install footings and post X2 for batten screen. Attach wood to steel post in prep for wooden battens. Install gate and fence across 2.5m entryway. Holes for fence have been dug. Materials available

I’m looking for someone to install two gates for us at either end of this side part of our house (please see picture). The gates would each be approximately 1200mm (W) x 1800 (H) with poles to hold these in place being roughly 2400m. One gate needs to have a barrel bolt as the way to open it. The other one needs to have a self-closing hinge so it can close automatically. This latter one would have a D-latch as the opening device. I’d appreciate you coming to take a quick look at the job to confirm feasibility, measurements and firm up a quote. We’d like to pay for the provider to supply the materials (eg from Bunnings) and build the gate.ideally we could get the job done or at least started in the next few weeks.

40m fence, need more hands on deck Lapped and capped, must have own tools and be competent

Edit: Require chain wire fence removed and timber fence installed. 10m long/wide and 4-5 posts.

We need to replace our front fence and pedestrian gate. Existing wooden rails of fence are rotten. However the posts are in excellent condition and can be kept. 6 fence sections require removal of rotten wood and replace with new rails and wooden palings. A matching replacement gate is also requested. The style of the fence can be simple picket style with flat or curved top. Painted to match house and existing metal car gate. Pool gate style lock (already on existing gate) preferred. 12.5 m. Gentle slope. 1.2m height right hand side of pic to 1.38 on left near driveway gate.

Replace or repair hinges on the steel gate to the bin enclosure. The gate is catching on the frame because the hinges were slightly bent I think. The gate closes but I have to lift and push which is still scratching the frame. The enclosure is outside and you can come anytime to have a look/price