Find trusted local electricians in ACT

I have two matching outdoor wall lights that require repair. Both lights have developed the same fault: the large metal shade/lamp-holder section has separated from the smaller upper bell attached to the gooseneck arm. The original metal fittings, shades and glass covers are all in good condition and I want to retain the existing lights rather than replace them. From inspection, the issue appears to be with the internal E27 lamp-holder/mounting assembly. The plastic lamp-holder and/or the hardware that mechanically connects it to the mounting bracket inside the upper bell appears to have failed with age. I’m looking for a licensed electrician who can: * Repair 2 identical fittings. * Inspect the existing E27 lamp-holder and internal mounting arrangement. * Replace the lamp-holder and/or threaded nipple, retaining hardware or mounting components as required. * Mechanically secure the large shade back to the upper bell so the fitting is properly supported. * Reconnect/terminate the existing wiring correctly. * Check that the conductors have not been damaged or strained. * Refit the existing glass covers and bulbs. * Ensure the fittings remain suitable/weather-protected for outdoor use. * Test both lights for safe operation once completed. Important: I would strongly prefer to preserve the existing metal shades, gooseneck arms, wall plates and glass, as the lights match the architecture of the house. The failed internal components appear relatively standard, so I expect suitable replacement E27 lamp-holders/mounting hardware can be sourced rather than replacing the entire light fitting. Photos attached show: 1. the failed fittings and exposed mounting hardware; 2. the lamp-holder assembly; 3. an intact matching light showing how the completed fitting should sit. Happy for the electrician to either supply the required parts or advise what needs to be purchased. Please include/indicate parts separately from labour if possible.

I need A EV Wall Charger installed. I have the charger but need it to be installed.My house also has solar or 13kw and a battery of 42kw. I have a single phased switch board

Looking for ev charger for single phase which will be installed next to the switch board.

Need someone to install and design simple outdoor Christmas lights. Lights haven’t been purchased yet so will take your advice on what to buy/ how many etc. single story house with partial pitched roof. Experience preferred. Price negotiation able for the right person.

Need to install two power point in garage

Must be licensed and will require proof via license number - thanks for understanding Would you be able to quote for this please: • Install a bedroom artwork light with a new wall switch • Install one new double power point inside the bedroom wardrobe • Install a bathroom vanity light once it arrives Full access available from roof cavity above The bathroom light hasn’t arrived yet, so that installation would require a second visit. We’re happy to commit to the full job and pay the total agreed price upfront. Please provide a total price?

Replace 250V 15 Amp IP54 Outdoor single Power Point with 250V 15 Amp IP54 Outdoor Double Power Point

Cracked in the middle and needs replacing - lights and fan still work

I have a brand-new Geely 7kW Type 2 EV Home Wall Charger, which I will supply. My newly built house already has a dedicated EV charging outlet/connection installed in the garage by the builder. The EV circuit was installed as part of the original electrical installation and was confirmed by the builder/electrician at handover as being for EV charging. I am simply looking for a qualified/licensed electrician to connect the supplied Geely wall charger to the existing EV connection. Existing EV infrastructure The switchboard appears to have a dedicated EV circuit labelled “GARAGE N/L 15”, protected by a: Hager ADM432T RCBO 32A 3P+N (three-phase + neutral) 30mA Type A RCD protection 230–415V AC Hager's technical specifications confirm the ADM432T is a 4-pole, 3P+N, 32A Type A 30mA RCBO, which is consistent with the dedicated three-phase EV circuit installed at the property. The garage also has the dedicated EV connection/isolator already installed. Work required Please: 1. Inspect the existing EV connection and confirm it is suitable for the supplied Geely 7kW charger. 2. Connect and securely mount the Geely 7kW Type 2 wall charger to the existing EV circuit. 3. Reuse the existing EV circuit and protection — no new circuit is required unless you identify a compliance or capacity issue. 4. Test the installation and charger under load. 5. Confirm correct RCD/earthing operation. 6. Provide the required electrical compliance documentation/certificate on completion. I am not looking to have a new EV circuit installed. The house already has the EV infrastructure; I just need the supplied wall charger connected to it by a qualified electrician. Charger: Geely 7kW EV Home Wall Charger – Type 2 Customer supplies charger: Yes Existing EV outlet/circuit: Yes New circuit required: No — unless electrician determines existing installation is unsuitable after inspection Job: Connect, mount, test and certify.

Looking for a licensed electrician to install and connect a new oven at my home. The old oven has already been removed and disposed of, so only the new oven needs to be installed and connected. Please bring your own tools and let me know your quote and availability.

Lamp switch is broken and lamp needs rewiring.

replace 4 dbl power points & 2 light switches

Tesla charger installation in Garage

Smoke alarm is beeping. Need to remove batteries ASAP. Ability to stand on a chair or small ladder required.

Hi I need some electrical RCD circuit breakers push button tested. Also a fire extinguisher maintenance tag punched. This is for the stores OH& S I don't need a certificate or documentation. It's in a small retail store, needs to be done one morning at 8:30am Monday-Friday. 10 minute job.

Looking for two existing power points in our living room to be converted from two to four outlets. Seeking a qualified electrician to provide new faceplates/materials and labour for combined fixed price.

Need a qualified sparkie to fit a Delta smart double touch switch. This will swap out a typical double switch for a toilet light and fan for a delta smart switch (bought from Bunnings. https://share.google/rS4iXqqqL0GGXaFe1 ) that will put the fan on a timer.

Downlight in kitchen not working after changing the bulb.

Ev charger removal wall mounted Disconnect from the electric mains.

Removing several power points from 2 walls in a office.