Find a cladding professional near you

Install WPC outdoor Cladding /composite I’m looking for an experienced person to install WPC wall cladding to the existing timber garden/retaining walls in my front yard, as shown in the attached photo. Colour - Teak Work required: 1. Front wall * Approximately 4.8m long * Height approximately 400mm * Approximately 600mm high around the planter box section * Install WPC cladding to both sides (front and back). * Install composite decking boards on the top 2. Walkway The walkway has timber walls on both sides (front and back) where the existing white/pebble area and pavers are located. * Right side: approximately 3.2m long * Left side: approximately 1.9m long * Install WPC cladding to pboth sides * Install composite decking boards along the top Important: * Please see the photos. I have added one sample pictures and it is how i expect it to be installed but both sides. Located Marsden Park.

Replace existing damaged cladding with new.

Need this repaired asap. Accidentally reversed into it

Some silicon patching around the wall and then underlay primer and weathertex / outdoor painting as per the two pictures as shown. Will need ladder as wall is 3-4m

Job Overview Total Area: ~32 sqm Height: ~5.2m (High access/ladder work required) Materials: All Cutek stripping, cleaning, and staining products will be supplied and paid for separately. Contractor Requirement: Must supply and use a decent, high-powered pressure washer, lsdder, brushes, rollers etc Scope of Work Strip Old Coating (Cutek Stripper) Apply Cutek stripping product to remove the remaining stubborn areas of the old film-forming coating. The timber is mostly sanded, but all leftover old coating must come off completely so the new oil can properly penetrate the timber. Restore & Clean (Cutek Cleaner) Apply Cutek cleaning/restoring product to deep-clean the wood grain and prepare the surface. Thorough pressure washing is required during this step. Stain & Seal (Cutek Wood Oil) Apply the Cutek oil/stain product evenly across the entire 32 sqm area, including the upper sections up to 5.2m high

Looking for someone to come out and quote small, single second-story wall on log kit-home. 25 square meters. Need it battened out over timber and clad in vertical Colorbond with custom flashings on the corners/log ends.

I would like someone to paint the external wood cladding above our entrance door. You will need to: A) Put down a drop sheet so the concrete doesn’t get damaged. B) Gently wash down the timber using a soft-bristle brush and a mild detergent or specialized timber cleaner to remove surface dust, salt, and organic growth. C) Paint the cladding with a specialised external wood protector (which I will purchase) D) Use your own paint brush Thanks

Replace a small section of cladding and remove an old ORG. And replace with a small grated drain

I have a long piece of light weight cladding that needs re installing The piece is long and an extra set of hands is needed No tools required You will be needed for 2-3 hours

Going provide cladding need it installed,

Strip timber sheet wall and ceiling cladding including skirting and architraves in the upstairs room approx 8.4 x4.8m room. Take debris downstairs and leave in pile to be disposed of. Additional labour work available at same property.

Looking for someone to help with caulking in a factory ,

External wall Eastern elevation cladding wall to be repainted 20m x 8m total area

Experinced carpenter for the supply and Installation of external timber cladding to the small wall areas as shown in photos. Works include site measure, preparation of existing surfaces, supply and installation of timber cladding,wall wrap and trims, sealing/weatherproofing of all joints and gaps, and finishing to match existing surrounds. Cladding material is circa 30 linear meter, example profile provided.

My husband is doing it himself so I'm trying to get extra hands to go faster. Putting cladding stones like photos on the outside wall.

Hey guys, looking for a solid chippy or experienced tradesperson to help me out with a new house extension. ​The timber frame is brand new and straight, and the sarking is already up. It's a straightforward site with easy, flat ground access all around. ​The Job: ​Install eaves around the perimeter. ​Install timber battens over the sarking, including fixing the cavity closures at the base of the wall. ​Install Weathertex Weathergroove cladding over the battens. This includes fitting the required Weathertex aluminium external/internal corners and off-stud vertical joiners. ​Measurements: Total cladding area is 42 square metres across 3 walls: ​Wall 1: 3m L x 3m H ​Wall 2: 3m L x 3m H ​Wall 3: 8m L x 3m H ​What's sorted: I am supplying all the materials (eave sheets, aluminium joiners, cavity closures, battens, cladding, and fixings) and they are sitting on site ready to go. When you put in a quote, just confirm you have worked with the Weathertex cavity system before and know how to handle their specific joining methods and clearances. Please provide a quote for the labor.

Needing exterior wall (area with timber studs) to be filled with insulation and then cladded over to keep the house protected from the elements. We will provide earthwool and foil insulation. Cladding will need to be purchased by tasker which we will reimbursed.

Need to install indoor cladding x 2 walls — Wall sizes - [ ] Wall 1 ( H 2700 x L 2400 ) - cladding already cut to size with 4 panel - [ ] Wall 2 (H 2400 x L 900) - this cladding size is H 2700 need to cut to size

Source and Replace the missing tile. I don’t have any spare. I have parts of the tile and a similar also broken tile. It’s a mosaic job. Check for any other loose tiles. Tile dimension 600 mm x 150 mm. Second storey accessible via balcony. Ask me any questions if needed!

Finish off cladding the side of the house boards onsite