Find a cladding professional near you

I have installed mdf Panelling around the kitchen (pictured) and it needs to be painted. 1 base coat and 2 top coats. Paint and brushes supplied and ready to go, I will also prep the area for you. All 3 coats need to be done tomorrow. Depending on time availability, I might do the base coat and it will be ready for the top coat before lunch time. Someone with attention to detail please. The photo of the complete kitchen is a render and how it will look once complete . There is another photo of an example of how much mdf cladding there is… This is a mock up before we had installed it. Job is in prospect

Looking for someone who can install wall cladding. We have all the materials

I need 2 weather boards removed, cement sheeting to run to roof line and then back under the roof, attached flush to the 3 beams. Cement sheet 1 (match current groove design) will need to be 2400W x about 600H and needs to be fixed and combined with the existing sheet. The second sheet needs to be hung from the roof, coming back out over the battery and attached to the 3 roof battens. sheet 2 will need to be about 1800W and about 900H. For the wall panel will need to install basic quad along the sides and top to finish it off and then paint it all (I have the paint).

Looking for an experienced carpenter or handy person to install timber cladding on an exterior/interior wall. ​Dimensions: 9 metres long by 2 metres high (Total: 18 square metres). ​Scope of Work: Labour only. I will supply the timber cladding, but you will need to bring all your own tools, fixings (if required), and equipment to complete the job. ​Location: Melton West, VIC.

Areas of external cladding (blue board) needs to be removed for an engineer's inspection of the frames & footings. About 6 -8 inspection holes are required. The material does not need to be salvaged. Also a floor inspection hole needs to be opened - material does not need to be salvaged.

Need to fix external cement sheet and seal it well so it won’t leak out break. Picture attached. Also fix the roof sheet leak. Pictures for your reference. It is laundry room. Wanted to get it done ASAP.

A section of exterior timber/cladding came off my house during strong winds and needs to be repaired/replaced. We also have a water leak coming through the ceiling inside the house. We’re not sure where the water is getting in from and would like someone to inspect it and identify the cause. The damaged area is quite high — approximately three storeys from ground level, as the granny flat is located above the garage. I’m looking for an experienced carpenter/builder who is able to safely work at this height and provide a quote for the repair. Please see attached photos for the damaged area Please provide your quote based on the photos and access requirements.

Have 3x wood cladding sheets, that need to be cut to fit horizontally across a wall. One board needs to be cut into an arch shape. Have pictures to provide more of an idea Price negotiable

I have a long piece of light weight cladding that needs re installing The piece is long and an extra set of hands is needed No tools required You will be needed for 2-3 hours

Going provide cladding need it installed,

Strip timber sheet wall and ceiling cladding including skirting and architraves in the upstairs room approx 8.4 x4.8m room. Take debris downstairs and leave in pile to be disposed of. Additional labour work available at same property.

Looking for someone to help with caulking in a factory ,

External wall Eastern elevation cladding wall to be repainted 20m x 8m total area

Experinced carpenter for the supply and Installation of external timber cladding to the small wall areas as shown in photos. Works include site measure, preparation of existing surfaces, supply and installation of timber cladding,wall wrap and trims, sealing/weatherproofing of all joints and gaps, and finishing to match existing surrounds. Cladding material is circa 30 linear meter, example profile provided.

My husband is doing it himself so I'm trying to get extra hands to go faster. Putting cladding stones like photos on the outside wall.

Hey guys, looking for a solid chippy or experienced tradesperson to help me out with a new house extension. ​The timber frame is brand new and straight, and the sarking is already up. It's a straightforward site with easy, flat ground access all around. ​The Job: ​Install eaves around the perimeter. ​Install timber battens over the sarking, including fixing the cavity closures at the base of the wall. ​Install Weathertex Weathergroove cladding over the battens. This includes fitting the required Weathertex aluminium external/internal corners and off-stud vertical joiners. ​Measurements: Total cladding area is 42 square metres across 3 walls: ​Wall 1: 3m L x 3m H ​Wall 2: 3m L x 3m H ​Wall 3: 8m L x 3m H ​What's sorted: I am supplying all the materials (eave sheets, aluminium joiners, cavity closures, battens, cladding, and fixings) and they are sitting on site ready to go. When you put in a quote, just confirm you have worked with the Weathertex cavity system before and know how to handle their specific joining methods and clearances. Please provide a quote for the labor.

Needing exterior wall (area with timber studs) to be filled with insulation and then cladded over to keep the house protected from the elements. We will provide earthwool and foil insulation. Cladding will need to be purchased by tasker which we will reimbursed.

Need to install indoor cladding x 2 walls — Wall sizes - [ ] Wall 1 ( H 2700 x L 2400 ) - cladding already cut to size with 4 panel - [ ] Wall 2 (H 2400 x L 900) - this cladding size is H 2700 need to cut to size

Source and Replace the missing tile. I don’t have any spare. I have parts of the tile and a similar also broken tile. It’s a mosaic job. Check for any other loose tiles. Tile dimension 600 mm x 150 mm. Second storey accessible via balcony. Ask me any questions if needed!