Find experienced local carpenters in WA

Looking for a joiner to come over and have a look at a project I want built.. I am making a music studio in the garage so want a set up where I can make music and also another set up so I can put my decks on. The Airtasker would need to scope job, order and pick wood up and I’ll pay on top of labour. If you think you can do it please offer $0 and you can come and scope the job out. Looking to get this done as soon as possible😊

Cabinet Maker / Joiner Needed – Custom IKEA PAX Wardrobes (2 Rooms) Looking for an experienced cabinet maker/joiner to customise existing IKEA PAX wardrobes to create a built-in look in two bedrooms. Existing wardrobes: • IKEA PAX units already installed (2350mm H x 3000mm W) Work required: • Build and install 600mm high overhead cabinets above the existing PAX units • Total finished height: 2942mm • Supply & install 12 x slim shaker doors (248 x 2344mm) – painted • Supply & install 12 x slim shaker doors (248 x 598mm) – painted • Install Blum soft-close hinges on all doors • Supply and install side panels/fillers to conceal gaps and create a built-in finish • Delivery and installation included Room size: 3500mm W x 3250mm H Notes: • Same work required in two bedrooms • Please quote for the full job • Photos attached for reference

I would like a qualified and skilled carpenter or joiner to reduce the width of my outdoor table. Its currently 1100mm wide, id like it reduced to 900mm. Sand edges smooth to finish.

I’m looking for an experienced joiner or carpenter to build the timber foundation only for a small benchtop retail display stand for my jewellery brand. This is a precision piece that will later be fitted with custom acrylic trays and signage, so accuracy and clean workmanship are important. You’ll be provided with a clear PDF showing the design and dimensions. Pricing isn’t accurate we can discuss materials and labour

I want to get laundry cabinets built and some doors made for an existing open shelving area. Please quote for labour and materials as I’m not sure yet if I will be getting the joinery materials myself. Good timely Carpenter or joiner needed. Potential ongoing work

Have almost installed small Apartment ikea kitchen but just need help finishing it off with a few tricky bits, kick boards, moving the oven cupboard over by 10cm, adding end panels, free standing Dishwasher trimming out, and we would like to trim out a wall around a fridge and above a tall pantry to the ceiling All with matching ikea end panels etc if possible - tried ourselves but lacking skills and tools so need a professional please

I bought a pullout rangehood and it doesn’t fit into my existing joinery. It’s off by mils as the lip on the laminate either side seems to be too thick or the cabinets have expanded over time. I need the cabinets either side trimmed up to make it fit and then for the rangehood to be installed. Rangehood specs: Height (mm) 175 mm Width (mm) 898 mm Depth (mm) 300 mm Model Number WRR904SB. Width of joinery is approx 894 mm.

Looks like the pipe has cracked underneath or is leaking out the flange. Have tried tightening it looks like it’s getting worse so I just need to replace that pipe in between. Have a ladder ready for roof access it’s at the front of the house. .

Need a joiner /plasterer to finish a small space as you enter the house and finished a newly build coat cupboard

Wooden kitchen bench alteration in situ. Laminated structural oregan pine Precise woodworking skills to detail cut current bench top to round off/semi-circle Fine finish/seal the edge profile to existing pencil round or similar to match - see close up image.

Damaged skirting under front counter needs replacing 1mm Aluminium Black Powdercoated roughly 150mm H - New Material is onsite - Need to cut and scribe to suit Overall length approx. 4.8M Please allow for rubbish removal 8am start at a shop in Hallarys Boat Harbour Thanks

Door needs additional wood support and new hinges

Hi, I’ve purchased x2 laminate benchtops from IKEA. One is to go on top of my IKEA 140cm long kitchen island bench (cabinets) that is already assembled. I need the benchtop cut to size and screw into ready to go frame, then use the 2nd benchtop to cut /install waterfall sides to the kitchen island. x4 cuts in total = *Cut each end of benchtop (x2 cuts) * Cut each waterfall piece for each side/end of island (x2 cuts) * Glue waterfall sides to benchtop. I’d like the job done after 1pm tomorrow 30th March. I’ll pay $300 if you’ll also screw in the back x2 panels (140cm wide in total) to back of island & install the kickboard to base of front of island. *Only experienced in this type of work to respond please. Want quality finish. Thank you.

Wall needs fixed, can use filler/bog for holes and cracked bits and smooth off. And joiners are missing and broken. Those also replaced/fixed where applicable. Some low spots also, as shown in photos. Filler and flushed off on those too. And then color matched to existing wall. Thankyou.

Having opening bricked up and installing a single door.

Storage Unit Mezzanine. Standard stud wall framing. Materials on site already. Stud walls around perimeter approx 4.5m x 5.5m

Need a custom built camper kitchen unit have sizes need a joiner to come size up and let me know

Easy tasks just need a top of a sprinkler head replaced with a new one and add a joiner with clamps to a split pipe. I don't have the tools so couldn't get it one myself. Prefer to have it done today. Thanks in advance

Repurpose TV unit into shelving units. TV unit is 3m 320cm length 55cm width 26 cm height Repurpose into tall shelves or shelving unit for those areas beside the next photo (fireplace)

I have an Ikea pax wardrobe that has been installed recently and I would like to finish wardrobe by installing the frame/joinery to create a flush look. One of the end requires a frame to be made to close off the gap. The width of the gap is 8cm.