Find experienced local carpenters in West Perth

To make 1 x custom plinth with the following dimensions: 30cm D x 45cm W x 100cm H To be made with MDF and painted in semi-gloss white. - Due date: Flexible

We have a mini flat pack shed we purchased online that needs erecting on a small piece of existing paving out the back of our clinic. Shed is 1:52mW x 0.78mD x 1.95mH - Due date: Flexible

Install 2 x 3.7 m skirting board and 1 x door. I will supply materials - Due date: Flexible

I don’t know where to start looking so perhaps someone on here can assist. I’m considering building a custom built in bed base for a toddler room with storage. The photo kind of resembles what I’m talking about (but just the bottom bit, not looking for the second floor walk up) - Due date: Flexible

the wood on the bottom panel of the door has split and is dragging on the ground - Due date: Flexible

I have one Kaboodle Pull Out FOGO Bin Base cabinet that needs putting together ASAP. Some minor maintenance on a Kaboodle kitchen drawer & Cabinet. - Due date: Before Friday, 4 November 2022

I have four built ins that are having cabinetry replaced, but the carpet is going in prior. This means I have to rip the existing cabinetry out before carpet goes in. There are five cavities with built ins to come out, all similar to those in pics. Once cabinetry comes out, we have to put skirting where the cabinetry was. - Due date: Before Thursday, 6 October 2022

We need to install a door to separate our office space located near West Perth. The door needs to be installed in the corridor as per the photos. The height is around 12ft. We need quotes for door installation and options for the doors.

Extend kitchen benchtop, cupboards beneath, tall panels around fridge, cupboard overhead fridge. Match existing laminex finish

HI - I am looking for an experienced wallpaper installer- my wall measures :Width: 8.6m Height: 5.66m - Due date: Flexible

I own a 1 bedroom apartment in West Perth. My galley kitchen and pull out pantry faces (draws and doors) are bubbled / worn and need replacing. Apparently they were former IKEA cabinets, but IKEA no longer stock the size. I am needing the cabinet faces to be measured and quoted, supplied, old ones removed and new ones installed. I’m just looking for a basic white - some gloss if possible. Photos attached. Measurements below (although I’ll require them remeasured to ensure accuracy!). Keen to get this job completed promptly, as I am waiting to list the property for sale. Pantry door 1940h x 400w Doors, 670h x 600w, 670h x 400w Pots drawer front, 260h x 600w Drawer fronts 125h x 600w x3, 310h x 600w x1 Oven fascia (lower cover plate), 90h x 600w - Due date: Flexible

Looking at bilding pergola patio deck etc - Due date: Flexible

Had to pull out 5 timber boards. looking to replace them and have them stained to match existing boards

Installation of a shed and three work benches, dimensions of these are seen in the photos. Looking for somone with experience in these type of tasks and who can supply their own tools - Due date: Flexible

GABLE H/SHED TYPE 1 Length (mm) 3,109 Width (mm) 3,865 Height (mm) 2,400 Roof sheet: CGI Premium Double Sided Wall sheet: superdek premium double sided Footing: fixed (in ground) Roller door: 1 This is the shed, however the size has been customized to fit our space slightly. https://www.stratco.com.au/au/sheds--garages/garages/gable-roof-sheds/domestic-gable-roof-shed-stubbie-3.16-x-3.16-x-2.4m-gable-end-roller-door-zincal-oghsty1domsrdaz/ The link includes specs & guidance on installation. Shed to be installed on brick paved flooring. Shed hasn’t been ordered yet, so installation date not known yet. Likely to be in 4-6 weeks time or so.

Stone bench top cutout by 5mm on length and width to fit new cooktop unit. - Due date: Before Thursday, 13th Jan 2022

I am after 3 floating shelves of the following dimensions: 1x 2500Lx250Dx5W cm 2x1000x 150Dx4W They need to be timber, Jarrah would be ideal but it would be subject to price.

Kitchen is being resurfaced but this part of the cabinet above the stove is somewhat warped. I’d like say a 3mm MDF be affixed as marked in the photos. It may require a light sanding prior to gluing/attaching. Being: -around the rangehood - on the two sides as marked and - underneath the cabinet as marked with the arrow The price offered is exclusive of materials which you would need to acquire from for which you’ll be reimbursed.

I have 3x Ikea Bror cabinets that need to be wall mounted (already built but will require dynobolts or screws to mount it) Also have 1 defibrillator that needs wall mounting (includes all its mounting parts) I will require a tax invoice as this is for a business.

need a cabinet maker to go to new office and price up cupboards for board room in west perth