Find experienced local carpenters in Outer East Melbourne

I need someone to replace and/or reinstall 4 hinges on a pantry/cabinet door. Door dimensions are approximately 72cm wide x 204cm tall, and the door is heavy (a solid MDF panel, not a lightweight panel). The current hinges need replacing or adjusting, and the door may need realignment so it closes/sits properly.

I have a timber bedframe which is creaking and when I looked where, I found that few of the screw holes are stripped and I ess unable to tighten the screws on one joint. I need someone to help fix this with a strong bond so it csn be drilled again. I tried Earl’s Timbermate wood filler but it did not work

Washroom and wardrobe doors are not closing properly needs to be fixed Bedroom room door is not holding the handle Lock properly

Looking for “post-and-wire” balustrades and handrails, as shown in the attached picture. Please quote for labour only; I’ll supply the materials. If you are a metal fabricator or kit supplier and installer, please quote for supply and installation. I’m open to either timber or metal options. I just need the basic version to comply with the building regulations.

Looking for an experienced cabinetmaker/joiner to manufacture and install custom cabinetry to both sides of our laundry. Wall 1: approx. 1900 mm wide. Design to include 2 × approx. 450 mm pull-out laundry hampers, a 1000 mm open space underneath for a dog bed, and overhead storage cupboards. Wall 2: alcove approx. 1780 mm wide × 450 mm deep × 2600 mm high. Design to include a 600 mm full-height storage cupboard, bench area, lower storage, floor-level open area for a robot vacuum, and a hanging rail above the bench. Cabinetry to be white with matching doors and hardware across both sides. I will source the stone benchtops separately. Cabinetmaker to construct the cabinetry ready for stone installation. Reference photos and design concepts available. Site visit and final measure required before fabrication. Please make an offer for cabinetry supply and installation only and provide examples of previous custom cabinetry/joinery work.

I have an unfinished job in the guest bathroom and need a carpenter to complete the remaining work. Please see the attached photos for the areas that need to be fixed and finished. The job also includes installing a door handle with a lock. Please review the photos and let me know if you can complete the work, along with your quote and availability. Thank you

It's on our roof. Place an offcut on damaged fascia with nail gun. This is just a temporary fix to weatherproof it until permanent repair is done. You need a ladder and nail gun. We have the offcut

Architrave around 2 windows on weatherboard. Please give two quotes in reply section: - Architraves provided by me - Architraves to be bought by you Window 1: 3200mm x 1360mm Window 2: 900mm x 600mm

Top of stair balustrade is loose and needs to be stabilized.

Hi, I am looking for an experienced carpenter or handyman to repair the bottom section of a wooden porch post. The bottom has severe wood rot, and two metal pins embedded in the concrete are now exposed. Please let me know your repair solution and provide a reasonable quote. I only need the structural repair done; I will handle the filling and painting myself later. I have attached a photo of the damage. Thanks!

This skirting board had some moisture damage in the bathroom on right side. The moisture has been fixed, but the skirting board was damaged and the backing has also collapsed in the damaged area. The length of the skirting board is approximately 22cm long x 6cm. I need the wall cavity packed out/patched and a new section of moisture-resistant skirting board fitted and sealed. No painting required. I am looking for a reliable local long-term handyman/carpenter for future jobs.

I need to make space for my double door fridge. The cabinet on the left needs to be moved a few cms (not fixed to floor) and the cabinet on top completely remove d for my fridge to fit. Must be available after 5 pm any day from today to Thursday

Need to reduce the overhead cabinet size above fridge space to accommodate bigger fridge. Once resized, overhead shelf door is no longer necessary.

I need some additional shelving in kitchn and laundry

Need help fixing the L shaped kitchen cabinet. Require a joinery expert or cabinet maker for this job.

Need an experienced carpenter/handyman to finish and adjust 4 internal doors in our house. Tasks include: * Fit and install door handles/latches on 4 doors * Trim/plane doors where required (some doors appear too large for the frame) * Align doors and catches so they latch correctly * Check overall fit and if you could paint the doors too thats even better All doors are already in place but have not been finished properly. Looking for someone with experience fitting internal doors and door hardware. Please bring the tools required for trimming and fitting doors

Looking for a skilled cabinet maker, carpenter, or handyman to build and install a custom floor-to-ceiling storage cabinet/pantry in my apartment, based on the attached sketch. The cabinet will be positioned around an existing structural column/wall and should maximise storage while maintaining a clean, modern look. Please provide your offer.

I'm trying to see if someone get make a custom vinyl record cabinet (see pictures for inspiration). I've been shopping around but cannot find anything like this. I want some sort of hinge with a door that opens up to uncover my audio-Technica turntable (Audio Technica LP60X USB Belt Drive). Underneath that, I'd like some sort of cavity to fit a speaker, then on the side, storage large enough for vinyl records (35cm high and 35cm deep). Below or on the side of that, I'd like some drawers or traditional cupboard doors for extra storage. I've included a sketch of a general idea but there is some flexibility there. I'm hoping to use a cheaper material like Laminex or similar material - it doesn't have to be solid timber as that is quite expensive.

Shave down 10mm from door with track saw and re install door ( door already has hinges just need to shave down height due to flooring) Ringwood located

Need to cut a round or square hole on this timber as marked. Anyone can help with this?