Find a professional staining service in NSW

We have a 5m long untreated wooden ceiling beam that requires an expert woodworker/painter to sand (if necessary), protect and oil/stain. We’ll be painting the ceiling and living room after, so want this beam to stand out and look beautiful. I can pay for and supply the stain but must come with all other equipment including 120 grit sander. Would also appreciate the removal of the existing hooks and nails (about 4).

Clean and stain pool deck.9 x5m Product will be supplied

Chef 54cm Stainless Steel Upright Freestanding Cooker CFG504SC, LPG converstion kit installation and conection to existing LPG gas supply

Hi, We have installed herringbone flooring. We would like to do satin staining for them without sanding the floorboards and without streaks. There are a few rooms; 1 formal room, 1 small study, 1 rumpus area, 1 master bedroom and 3 bedrooms Happy to further discuss.

Simon Says Juice. Based in Darlinghurst Sydney. Stainless steel bench. Nothing too tricky. Require a 10 cm diameter hole to be cut through it. Any man with the correct drillbit and a spare 30 minutes you can get it done. Don’t all rush at once!

room 3.5 x 4 m Floor sanding and stain, and add polyurithane

Remove cork from stairs, add new top e.g. vinyl, wood etc. potential stain or fix floor. Apartment is two levels approx 120 m2. Currently no furniture. Please give a quote.

Need someone to fabricate a Stainless steel snorkel for my Nissan Pathfinder R50 2003 I can come to you anywhere 2 hours from Sydney

Stain deck area. There are plants which need to be moved before staining. Deck paint will be provided. Deck dimensions 5 m × 5m

Our deck size is 28ft x 10ft approx It need to be stained No deck railing only deck floor side stairs Looking for reasonable offers only Avoid sending me too much Labor cost thanks

Brand new in Box- Kitchen Island Cart with Stainless Steel Countertop Please see image below

Hi there, I need to cut a flap on a stainless bench traced on the photo. Also drill 4-6 holes through stainless also.

Person must have experience in, and produce a good quality stain and sealant for my back deck, bench seat and upper rafts. May require sanding in some areas.

Apply two coats of deck sealant/stain to wooden deck area in Photo approximately 20 m² Also need about half a dozen minor repairs made and small areas with touchup painting etc. I will pay for a full days work and give list of activities.

I have 1 large stainless steel shelving unit and one tool bench to put together for my workshop.

Welding two pieces of stainless steel

My dog was very dehydrated and and pee'd on our floorboards and it instantly has left a stain that needs to be removed or at the very least significantly lightened/ improved upon. I am looking for a spot treatment just on the area in question.

I need a garden decking sanded and stained in our courtyard. It has not been sanded/stained in a couple of years so looking for the right person to help out! Happy for it to be done over a few days if necessary. the photos show the main total area that needs work. Located in Abbotsford

Job: Small Concrete Slab + Install Outdoor Shower (Northbridge NSW) When: Flexible, ideally within the next week Job Description: We’ve recently installed a new hot tub (photos attached) and are now adding a matching outdoor shower next to it. We need someone to: 1. Dig out and level the soil area shown in the photos (approx. 1m x 1m). 2. Pour and finish a small concrete slab so the shower base sits flush with the ground. 3. Mount and fix the stainless-steel shower onto the slab once it’s set. Requirements: • Experience with small concreting jobs or landscaping work • Supply your own materials, tools and concrete mix • Ensure neat finish and alignment with the existing paver edge Access: • Easy side access to backyard • Power and water available on site Goal: A clean, level concrete pad under the shower (see example photo of similar setup) that’s sturdy and flush with surrounding pavers.

Sanding, staining, and sealing of pictured deck. Last photo is what I’d like the result to resemble. Dimensions: approx 4.5m x 1.6m Will need to replace some nails that are sticking up, (or nail them back in). Work around some in-deck lights, and aircon unit. You bring all equipment and products please. Ask any questions!