Find experienced local carpenters in Outer East Melbourne

Sand & restain/lacquer etc to bring back to normal

Need to rework on the garage entrance door including slider as the door was hard to move

Need to assemble shoe rack and a cabinet

I am wanting to shift my wardrobe 600mm in order to create a linen cupboard on the other side. Need to remove 1-2 studs in load bearing wall in order to open up hallway wall for linen cupboard. New wardrobe face to line up with the corner of the wall in photo

The sill and lower frame where window meets sill is soft and rotted.

I need three cupboards and three draws made up and the substrate for an outdoor bbq . I already have the stone mason , the benchtop will be 80mm so need to make the substrate to handle that, and there is an outdoor fridge which will need cabinetry around it so the water fall ends can stick to it. Just added a photo of what it will look like when the stone masons have finished

I’m looking for a tradie to replace weatherboard and basic timber planks on the out side of my house. The main issue is a damaged plank with a hole caused by age, deterioration, and what appears to be birds gradually picking at the wood. The entire plank (vertical) needs replacing/repairing. It is located on the second level which is only an attic, and access is available. See the photos.

I’m after steps for the front entrance of my house. Deck height - 600mm Width of stairs - 1500mm 3 steps staircase with Balustrading and handrail

I am currently looking for a quote only, not to start the work yet. I need a licensed carpenter to remove an existing non-load-bearing internal timber wall, approximately 1.5 metres long. I would then like a new non-load-bearing timber wall built, approximately 2.5 metres long and 2.4 metres high. The quote should include labour and all required materials. Please provide a total estimated price for the complete job. A valid carpenter’s licence is required.

4 bedrooms plus the walk and associated walk ins and wadrobes, a walkway which has steps at either end (8 in total) and a living room. Area is covering 70m2 and would like it to be re stained

Looking carpenter or labourer to build a frame, to increased the height of the Nib wall by 300mm. Frame required - aprox 3000mm x300mm x 125mm Note: The shelving cabinetry is not fixed, it’s sitting on the bench, waiting to be hung.

I need to make space for my double door fridge. The cabinet on the left needs to be moved a few cms (not fixed to floor) and the cabinet on top completely remove d for my fridge to fit. Must be available after 5 pm any day from today to Thursday

Need to reduce the overhead cabinet size above fridge space to accommodate bigger fridge. Once resized, overhead shelf door is no longer necessary.

I need some additional shelving in kitchn and laundry

Need help fixing the L shaped kitchen cabinet. Require a joinery expert or cabinet maker for this job.

Need an experienced carpenter/handyman to finish and adjust 4 internal doors in our house. Tasks include: * Fit and install door handles/latches on 4 doors * Trim/plane doors where required (some doors appear too large for the frame) * Align doors and catches so they latch correctly * Check overall fit and if you could paint the doors too thats even better All doors are already in place but have not been finished properly. Looking for someone with experience fitting internal doors and door hardware. Please bring the tools required for trimming and fitting doors

Looking for a skilled cabinet maker, carpenter, or handyman to build and install a custom floor-to-ceiling storage cabinet/pantry in my apartment, based on the attached sketch. The cabinet will be positioned around an existing structural column/wall and should maximise storage while maintaining a clean, modern look. Please provide your offer.

I'm trying to see if someone get make a custom vinyl record cabinet (see pictures for inspiration). I've been shopping around but cannot find anything like this. I want some sort of hinge with a door that opens up to uncover my audio-Technica turntable (Audio Technica LP60X USB Belt Drive). Underneath that, I'd like some sort of cavity to fit a speaker, then on the side, storage large enough for vinyl records (35cm high and 35cm deep). Below or on the side of that, I'd like some drawers or traditional cupboard doors for extra storage. I've included a sketch of a general idea but there is some flexibility there. I'm hoping to use a cheaper material like Laminex or similar material - it doesn't have to be solid timber as that is quite expensive.

Shave down 10mm from door with track saw and re install door ( door already has hinges just need to shave down height due to flooring) Ringwood located

Need to cut a round or square hole on this timber as marked. Anyone can help with this?