Find experienced local carpenters in North West Melbourne

Need to box out an area in a warehouse office roof. The area is 1000mm x 1000mm x 1500mm. The ceiling is plastered with clear access to the roof. On top of the office is chipboard. Timber for the job is supplied. Need the roof cutout, boxing made up and installed. Plastering isn’t part of this task.

Need custom cabinetry done around the top and base of a fishtank in black Top 540 x 750 x 2840 approx Bottom is 1170 high by 750 x 2840 approximately ok so basically just putting panels around the the frame but the tops need to lift up for access to the water

I m looking for someone to repair or replace the laminex of a cabinet one door near kitchen asap because I have inspection coming soon

Im after this piece of wood to be sanded, planed flat ready to be made into a table top

Sand front door and light stain.

Sand and stain timber doors, front is double door and one laundry door. UV protection stain or clear coat.

need a carpenter to repair four specific rotting timber posts across two structures: • Structure 1: One post with rot at the top; one post with minor rot at the base. • Structure 2: Two posts with significant rot at the base. Please assess the depth of decay. Quote for cleaning, treating, or replacing these posts to ensure structural stability.

Looking for an experienced cabinet installer/carpenter to supply and install: • Overhead cabinets above laundry area (approx. 180cm W x 60cm H x 80cm D) • Timber or laminated waterproof benchtop (approx. 140cm W x 70cm D), aligned to sink height • Caulking and sealing of all edges for water protection • Cabinetry white linen Natural Laminex finish, Hettich soft-close hardware Photos of area have been attached for reference. Measurements and details can be confirmed on site. aprx. $1500 budget

I need someone to help me with little DIY work. Changing cupboard to display. I will upload before and after photos

I want the following shown in the picture to be built, I want it however to be starting at 60cm and goes up higher by 10cm for three rows, ending at 80cm I really hope that makes sense!

4m long shelves requires in garage with doors for storage.

Looking to install a 60cm dishwasher in our kitchen, this will require a refit of a 45cm wide cabinet (pictured open below) and necessary adjustment of an adjacent 90cm cabinet. No urgency and flexible to day of week/time of day for this refit. Many thanks in advance

Hi, I have two small carpentry repairs at home: 1. One stair baluster has come loose at the bottom and can be lifted off — needs re-securing. 2. Two doors cannot latch properly and needs adjustment. Could you provide a quote or availability to fix both?

Need a timber border to be added around a grave, I will attach a couple of photos for reference. I believe 4 pieces of timber is required. Approx size below. 2x1.2m 2x2.4m

This task is to pressure wash and decontaminate a deck installed last year and apply two coats of stain to deck after cleaned and dried. This job will have to be carried out over three days. Day one clean deck Day two first coat Day three second coat Care taken to not coat rock work, brick work or concreting when applying stain Area approximately 50m2 All furniture and loose debris will Be removed prior to start day Stain and cleaner will be supplied

I need a qualified cabinet maker or handyman with cabinetry experience to come out and adjust the cabinets around my laundry washing machine space. The current cabinets are slightly uneven/misaligned, and I’m unable to slide the washing machine into the space. Task details: • Adjust/straighten existing cabinets so they sit flush and aligned • Ensure the washing machine space is the correct width and clearances • No major rebuild required—just adjustments to allow the machine to fit properly • Bring any tools needed for small cabinetry fixes (e.g., hinges, screws, levelling tools)

Description: I need a welder to permanently attach 2 threaded bulkheads to a large stainless steel pot. The silicon O-rings aren't providing an adequate seal, so I want them welded in place. Details: Material: Stainless steel pot Job: Weld 2 bulkheads (there's already 1 existing bulkhead on the lid - see first photo) Locations: First bulkhead: On the lid (flat surface) - will be the 2nd bulkhead on the lid Second bulkhead: On the side of the pot (curved surface) The pot will have 3 bulkheads total when finished - only 2 need welding. Looking for someone experienced with stainless steel welding who can ensure a clean, watertight seal.

I'm looking for two wall kitchen cabinets, each measuring 80x80cm, to be installed. Additionally, I need one more cabinet that fits above the fridge, with dimensions 60x80cm.

Install three shoe cabinets for me from Temple and Webster - I attempted to do one and I can’t be bothered doing them

Solid timber staircase needing sand and stain to refresh