Find a local Tasker to help you make a kitchen cabinet in WA

Would like an additional row or cabinets from Ikea added to these upper cabinets. They are standard sizes, so they’ll hopefully just need to be measured, picked up and fitted. I’ll pay for the cabinets separately. I’m just looking for someone who can get the right sizes and fit / install them ASAP, before this house goes on the market. I’ve included pictures of the existing kitchen, the cabinet type / doors I would like from ikea, and the plans from when the house was originally built, for measurements reference. This only shows the lower cabinets, but it will help with the measurements.

Renovating my kitchen in Dunsborough (WA 6281) — need the old base cabinets (8 units) and 6 m Corian benchtop removed and placed in the skip. No disposal or transport required. Flat access and plumbing already disconnected.

Installation of kitchen cabinets. Almost 6, along with some drawers and bench top as well. Looking for someone reasonable.

Looking for a cabinet maker or someone similar to build and install a butlers kitchen cabinets for me

I need kitchen cabinet maker for only wall cabinets

Need (1) small base cupboard made 350mm wide. 540mm depth height approx 885mm door has been ordered separately. 1 x microwave shelf needed Also need 3 floating shelves installed, shelves are already purchased

I need a carpenter or cabinetmaker to adjust my existing kitchen oven cavity to fit a new 600mm (W) x 600mm (H) built-in oven Current size is 545mm (W) 650mm (H)

We would like ikea cabinetry installed for our kitchen renovation. We will have 3 straight sections of cabinetry in a line. See images attached. Budget is flexible to some extent.

Our kitchen cabinet doors need fixing as the surface is starting to peel.

I have a kaboodle kitchen to install. I have all the plans ready to go

Kitchen cabinet needs adjusting to fit a dishwasher in.

Looking for carpenter or similar to modify my kitchen cabinets for dishwasher install Located Waikiki

Alter an existing kitchen cabinets to fit a dishwasher. Existing conditions * The existing kitchen cabinets each have an internal width of 470 mm, fitted with timber doors. * A water filter is currently installed inside the circled cabinet. * The 40 mm granite benchtop is structurally supported by the rear, side separating cabinet partitions, & front cabinet frame. * The partition walls are typically double 18 MDF boards. Refer to photo. * The circled cabinet is positioned between the sink cabinet on left & a drawer cabinet on right. * The sink cabinet is a double-width unit, with 180 mm of clearance from face of the partition wall to the edge of the sink basin. * Water and power provisions already exist within the sink cabinet, but are located at the far end from the intended dishwasher. Scope of Works 1. Remove the existing cabinet door from the circled cabinet. 2. Relocate the water filter to the sink cabinet, ensuring it is securely mounted & accessible. 3. Modify the circled cabinet to create space for 600 dishwasher by: * Cutting the cabinets base flush with the floor. * Shifting the partition wall 150 mm into the sink cabinet, increasing the width to 610+ mm . 4. Alter the affected sink cabinet door by 150 mm, to ensure both doors are fully operable. 5. Install a new water supply pipe, from the existing water provision in the sink cabinet with shut-off tap. 6. Install a new drainage hose, and connect it to the existing sink drain trap. 7. Retain the existing power point if it meets safety & compliance requirements.

The surface of the kitchen cabinet doors are starting to peel off, and some parts are torn.

Needing the cabinet/board above the oven to be re done and made longer to sit flush with top off oven, price is rough as not sure what it will cost

1 broken drawer needs corners glued and new bottom. Other 2 fine but could do with corners reglueing and I may like new bottoms ( more solid)

Install kitchen cabinets Install bench top and cut holes for sink and stove Put cubboard on wall and around fridge

I'd like to remove the shelves (where the micowave is) and open up the counter space below, however I am concerned that the overhead cabinets do not seem to be attached to either the celing or the wall (and so these may be unsable if the shelving is removed). Ideally I would like to keep the overhead cabinets as they match the rest of the kitcen layout. Additionally I wouldn't mind adjusting the depth of the top draw to be a few cm deeper (which would probably require modifying the draws below as well). I am looking for advice on how to go about achieving this and then probably some help installing the decided solution. It would be great to have someone come take a look and help come up with a plan.

The old kitchen cabinets need to be demolished for installing new ones. The materials and design plan for the cabinets have been completed at IKEA, and construction can start at any time.

I want a pantry fitted between the fridge and wall and want it to match the rest of the cabinetry in the kitchen (my pantry is too small) - see photos of position next to the fridge 47cm wide, 186cm tall, 60.6 deep