Find experienced local carpenters in Enoggera

Hey im wanting the top of my gate extended I believe its alluminium After 50mm box, 60cm on the sides, aprox 530cm across After on site supply/install, just the extend, no paint ect Thank you - Due date: Flexible

Cat net and material will be ordered through catnet company. Person installing will need to bring his own tools for installations. - Due date: Flexible

I have a 60cm wife sieve above the hws in a small unit that desperately needs storage for suitcases etc There are pipes attached to the wall that you will need to jigsaw around to fit Supply and install required Have photo of space to see what you have to work with - Due date: Flexible

There are small gaps along some kitchen cabinets that require patching to improve pest control and water proofing in this area. The gaps are in the dishwasher space. It would require moving the current dishwasher in order to patch the gaps. - Due date: Flexible

We need someone with the appropriate tools and qualifications to finish assembling our 3x3 shed. Unfortunately the landscaper we contracted did not complete the job for us, and we had to finish assembling it ourself. The doors are yet to be put on, and last night the roof blew off in the wind, bending a few panels of the shed in the process. - Due date: Flexible

Hi, I am after quotes to help convert a double wardrobe into a office/study space. The pictures are ideas that I have only.

Cutting ikea plank to size required for kick board approx 600mm wide and 76mm high. - Due date: Flexible

Hi, We’re a childcare centre in enoggera and we need two cots to be built, i’ve attached an image of what the cot looks like for reference. Must be fully covid vaccinated with certificate proof.

Installation of shed (3mW x 2.26mD x 2mH) & concrete slap. It will be finished until end of Jan.

- Room is ~6.6mx3.1m. Actual width/area will be slightly larger when considering rake of ceiling - Existing ceiling in dining room will be removed by client - To form a raked ceiling to match the kitchen (slope of existing rafter) - To batten/joist out as needed to form the ~150mm deep zone required for insulation and air gap. Battens/joists need to be at 400mm centers as per MDF sheet requirements. To have MGP10 H2 140x35 joists (2 number spanning the ~6.6m length of room).Ceiling battens to run perpendicular to joists and be spaced at 400mm c/c - Install Bradford R3.0 with Anticon (foil faced) - Install trims/architraves/cornice etc around perimeter - Install VJ beaded MDF sheeting to match kitchen ceiling (~85-90mm centres, to confirm). 9mm MR MDF Lining or better - Prepare wall around bifold door and louvre with plasterboard etc to provide a seamless wall. To be prepared to be ready to be painted (client to paint) - Work with electrician (client to provide) to pull cables and install lighting etc - All waste to be removed - QBCC insurance To be included -All materials to be provided by the installer UNO Due date: Flexible

timber crates taken away (give Away) free rideon crates - Due date: Flexible

I have two double acoustic pool pump cover to build and place over pumps. Urgent job. Pkease finished before Monday. 1st nov See product in link: https://www.acousticbox.com.au/plugin/products/category/2028mm-wide-enclosures

As the above indicates. I would like to get prices to have the back deck sanded and stained. Just seeing what pricing is like And weighing up weather to do it myself or pay someone.

To repair-sand and stain the scratches my dogs have made on the front door of a rental. It has been previously fixed. These scratches are fresh in the door, over the putty that was used.

Hello, I need a 60-70 mm hole put into a timber bench that is about 60 mm thick. There are also about 4 under bench shelves that need to be removed. They’re made out of Pine

Hi, I am looking for a quote for 2 built in wardrobes (supply and install) from a carpenter/labourer/cabinetmaker. Measurements are to be ~650D x 2100H and one will be ~1750W and one will be ~1350W. To have mirror sliding doors and wont need a floor or rear wall as will be built into single skin VJ walls but will need a top panel and side panels. Will also need you to provide the shelving, drawers, racks etc. Quote to allow for ALL materials and labour.

We’ve just purchased a cubby house that will require dismantling, transport and reinstallation. The pick up location is at Mango Hill and setup location is at Enoggera As for the cubby house, it’s dimensions are approximately - 1.7m height, 1.5m long and 2/2.2m wide along the front. It comes off wall by wall, the slab is one piece as is the roof. Will need some handyman/building skill to take down and reinstall plus a ute to take it away. We do not have tools and cannot assist with dismantling or reinstallation.

I need someone to build a wooden teepee for my childcare centre. Photo attached

Timber shoe selves - 4 shelves, timber (we haven't settled on a colour yet, black in photos is an example), each shelf 40mm thick 350mm deep. Bottom shelf resting on floor, each shelf 200mm up from shelf below. All secured to studs. Shelves going around corner, approx ~1240mm long first section and ~1010mm for around bend. Please see attached crappy sketch for an idea of job.

Large scratch on wooden floors needs to be repaired aswell as marks from office chair, photos attached Not sure how much this would cost so please quote