Find a professional bricklayer in South West Perth

I’m looking for an experienced bricklayer to brick up an existing 1500mm x 1000mm window opening in a double brick home in Yangebup. Details: • Double brick construction • I will remove the window prior to work starting • I have an approved building permit and structural engineer plans I will supply: • Face bricks • Common bricks • Brick ties • Brick sand and cement Scope of work: • Brick up window opening • Install brick ties as per engineer’s drawings • Ensure work complies with plans and permit requirements • Clean and tidy finish Must have: • Bricklaying experience • Own tools • Ability to follow engineer plans Location: Yangebup Flexible with timing as i will need to organise getting the bricks, sand + cement & brick ties.

I have a steel beam porch pole at the front entry of my house that I would like to cover with bricks, roughly would take 150 bricks. Open to suggestions, material supplied.

We need to build a new front Fence through a registered builder. Council approved plans are available.

Looking to have a raise garden bed built. •Height = roughly 500mm •Shorter length section = 1500mm • Longer length section (fence line) = 6000mm • Total length = 7500mm Pricing to be inclusive of supply and install, footings, render and all bricklaying. We can paint the render and waterproof ourselves. Location is Kardinya. Note photo attached is AI generated to provide indication of requirements.

I need to remove 2 courses of brick to raise the height of an access penetration (Double Doorway) between two adjacent buildings; approx 250mm high x 1600mm width. One building wall is 125mm precast panel to be drilled in corners and cut and the other wall is a double leaf brick wall, that requires 2 course removed and two steel lintels installed (150x90x8). Leintels to be epoxy painted or galv. Mortor to be used around lintels once installed, all rubbish to be removed. Brick walls to be "Acrow" propped whilst lintel is installed, refer to drawing attached. Note: - work to be completed after hours, preferably on a Sunday.

I have one brick that needs replacing in a small set of steps. I don't have concrete or tools but I do have a brick. Job to be done after 2.30pm.

Repair brick wall and wrought iron fence

We need the brick wall cut back straight and one course to be added like other wall

Add Half-Blocks Capping to Existing Limestone Wall Description: Looking for an experienced bricklayer / mason to add one layer of half limestone blocks on top of an existing limestone wall. Job details: • Approx 5 metres long • Full blocks to be cut in half on site to create a neat capping layer • Brickwork to be straight, level, and well finished • Existing limestone wall already in place Location: 📍 East Fremantle, WA Timing: Completed by end of next week Materials: All limestone is onsite, can supply mortar.

brick repair, needs patched or replaced

I need a double brick wall filled in where a window was. Standard 230x76 bricks. Colour doesn't matter as it will be covered on both sides. Will clear out bricks and can assist getting half bricks out on the sides. Hole is 960wx1470h. Prefer air tasker to provide materials. Have a concrete mixer that can be used.

Reveres into Brick latter box

Build a besa block water fall for this area. I will remove this which is in place. Can supply blocks if needed

Bricks removed from external wall per photos due to leaking pipe. Need new bricks put in. We don’t have the brown/reddish coloured bricks as spares so will need to be supplied.

Hello all. We have council approval to raise up our external brick fence to a common height. This requires the existing brick piers to have additional courses added to the top. I have done a drawing of the required extensions, as well as the infill panels I'm going to install myself - but hopefully you can see what's required. We have enough existing bricks from around the house to do the work, but the critical thing will be to get the extension to look seamless - as close to the original brickwork as possible. Per the photos, there are 3 bricks per course - so see below qty required. Pillar 1 = 3 courses (9 bricks) Pillar 2 = 6 courses (18 bricks) Pillar 3 = 9 courses (27 bricks) Pillar 4 = 12 courses (36 bricks) Pillar 5 = 12 courses (36 bricks) Pillar 6 = 9 courses (27 bricks) Pillar 7 = 6 courses (18 bricks) (Total = 171 bricks) I will provide the bricks but all other materials needs to be supplied by the bricklayer. Thanks guys. Thanks!

Bought a fridge but it's a smidgen too big for the space. Need to shave bricks approximately 1 to 2cm on left side wall to make fridge recess wider.

13,400mm x 500mm rendered brick wall. To sit on existing brick plinth.

Build up once course of bricks into a pre existing wall

multiple bricks needs patched to look as close to normal as possible or replaced, Materials need supplied

Redoing the brick paving to accommodate the newly installed gate track. Need to raise level so that car won’t impact track when it drives over it. I started the job to replace one side up to the newly installed gate track and whilst I think I did a decent job on the first side I think someone else will be able to do the other side quicker and better than me! May seek an opinion on whether first side has been done sufficiently and consider getting it redone In summary - Pull back a couple more rows of bricks on side that needs the most raising (so that there isn’t a steep ramp) - Add and spread sand (I have 2.5 bags which is hopefully enough but maybe some other base also recommended) to raise level up to above gate track (allowing for settling) and level with other side - Compact - Re-lay bricks with original pattern -Fill cracks with paving sand (I have 1.5bags) This is for labour only but if other products recommended will purchase. It is my best guess based on how long the first side took me on assumption someone with experience in paving and right equipment will be able to do it in 2-3hrs but open to negotiation on that or paying more if it turns out to be a bigger job than I’ve explained