Find local bathroom renovation experts in Sydney

Remove mouldy shower silicone, thoroughly clean the area, and reseal with new bathroom-grade silicone. Floor area only. Must be completed neatly and professionally. Small shower area

1 x SHOWER refresh required - Shower floor area: approx. 1600 mm × 800 mm -Thoroughly clean and prepare all surfaces before application -Remove old, discoloured, mouldy silicone where required and apply new mould-resistant, watertight, bathroom-grade silicone -Leave most grout as is but regrout sections that are cracked (see photos). I believe the previous tiler (5 years ago) used epoxy grout. -To use own tools and supplies. Professional finish

I need a full bathroom renovations with the removal of bathtub and replacing with walk in shower new wash basin floor and wall tiling.

Looking to install the following: - Nero Builder Project Hand Shower Rail - Brushed Nickel - Nero Celia Wall Mixer - Brushed Nickel - Nero Celia Basin Mixer - Brushed Nickel This will be a straight like-for-like swap at existing outlet points (no new plumbing runs required) Flexible on date and time in the next two weeks

Someone to please clean the bathroom (including taking the fan cover off and removing lint from the vent). And then please putting new silicone down on the shower and at the base of the loo, because water leaks out of the shower at the moment. And then if possible it would be great to have assistance repairing the soap shelf that has fallen off/broken, although I don’t know if this bit is possible? Thanks

Looking for an experienced person to remove and replace the silicone edging/seal on 1 edge of my shower - 800mm. The existing silicone is old/discoloured and I'd like it removed, the area cleaned/prepared and new bathroom grade, mould-resistant silicone applied. May require grout. I'm looking for a clean, neat and professional finish so the shower looks fresh and new. Please only respond if you have experience with shower/bathroom silicone work. Photos of previous work would be appreciated. Please provide your quote and availability. Thanks

Looking for a licensed and insured builder experienced in aged-care home modifications to help with a bathroom renovation/modification for an elderly person in Marrickville, NSW 2204. The builder must have experience working with My Aged Care / Support at Home funding or aged-care providers and be familiar with accessibility requirements. Please comment or send me a message with your details, experience and examples of previous work. • Registered with Aged Care • Onboarded with Lumia Care • Demonstrated prior experience with bathroom modifications They hade their own builders but the price the said was ridiculous, I like things honest , even if you take it in they’re a drafted copy of how this bathroom needs to be done and you will need to work with them at Lumia and comply with their rules .

Need an experienced bathroom sealing/waterproofing professional ASAP. I attempted to remove some mouldy silicone and reseal the shower myself, but the seal has failed and water has leaked through, so I’d like it fixed properly. Job includes: * Remove the failed silicone seal along one side of the shower (approx. the length of the shower). * Clean and prepare the area thoroughly. * Apply a professional-quality, mould-resistant bathroom silicone. * Check for any gaps that may allow water to escape and ensure the shower is fully watertight. It’s only a small job (one long edge of the shower), but I’d like someone with experience in bathroom sealing rather than a general handyman. Please bring all tools and materials.

Need to reseal a shower. Seal has gone mouldy.

Need a handyman to help re-install towel rail and install new bath spout/faucet (tap itself is fine). Reimbursement given if new towel rail is needed. Happy for you to inspect first or send images to see work required/replacement parts needed before completing the job.

Replace mouldy shower silicone and install shower door water seal Please note I am looking for silicone replacement, not just mould cleaning.

Need new silicone in the shower area. There is mould under the silicone, I just need some fresh silicone around the base of the shower and a little outside of the shower. I’ve attached a photo of the colour of the original grout- light grey.

small budget bathroom renovation,

Help removing the fixtures. Help replacing the new fixtures.

Need shower resealed in bathroom. Existing silicone is old/cracked and needs to be removed and replaced with new waterproof, mould-resistant sealant. Looking for someone experienced with bathroom sealing and silicone work.

Waterproofing, tiles, gyprock cornice replacement and ceiling, new wall hung vanity, toilet,

I want to renovate a bathroom. It will involve removing all existing tiles and fixtures plus nib wall, re-waterproofing, tiling, building in a bathtub. Then install new bathtub (where exisiting shower is), basin, vanity/sink (slight move from exisiting location on wall) and toilet (same location). This would be a multi-task form since the limit on this platform is under-budget.

I need the existing silicone seals around the shower floor stripping and replacing. The shower area is approx. 1m by 2m. The previous silicons is only 2 years old and is already peeling off, so I'm looking for a quality solution. Happy to purchase the silicone itself if that's best for the premium stuff.

Reseal shower as it is leaking

Hi, I’m looking for an experienced installer (ideally glazier or bathroom specialist) for a small bathroom update. Scope of work: * Remove existing U-shaped shower rod and patch/repair tile holes * Remove old silicone around shower base and re-seal properly (waterproof joints) * Supply and install a fixed frameless arched (please see photos for reference) glass panel (approx. 50–70cm wide, ~2m high) on the toilet-facing side of the shower * Ensure clean finish with colour-matched silicone (tiles are travertine-look) Bathroom setup: * Open walk-in shower with a raised hob * Panel will only be installed on one side (toilet side), no panel on washing machine side * Goal is to reduce splash and improve waterproofing Requirements: * Experience with frameless shower glass installation * Must be comfortable drilling into tile without damage * Please specify: * Glass thickness (expecting ~10mm toughened glass) * Mounting method (brackets vs channel) * Whether supply of glass is included Notes: * Photo attached for reference * Looking for a clean, long-lasting result (not a quick patch job)