Find experienced auto electricians in South Brisbane

Vehicle Signage Installation – Hino 300 Series Truck Looking for an experienced vehicle signage installer to apply supplied vinyl decals to a Hino 300 Series truck with an enclosed box body. Job Details: Install approximately 20 vinyl decals of varying sizes. Decals are supplied. A mock-up with photos showing the required placement will be provided. Installation is required on the enclosed box body of the truck. Location: Acacia Ridge, QLD (onsite). Preferred Timing: Saturday preferred. We'd like the job completed in a single day. Please provide: Your quote. Availability. Details of your experience installing vehicle signage or vinyl graphics. We're looking for someone with experience who can complete a clean, professional installation.

Need to supply and install 80 channel uhf radio on a isuzu agitator truck

Change headlight for 2007 Honda Jazz. I supply the globe.

Need a sub and speakers installed

My sons Colorado is stopping randomly- our mechanic said it’s a wire issue

Need someone to remove and replace the starter motor in my 2010 Hyundai i30 CRDi diesel automatic. I already have the new replacement starter motor part, which I was informed would fit my vehicle from the seller. There is an oil leak around the engine area which may have contributed to the old starter failing, so just mentioning that upfront. I also just purchased a new battery. At this stage I mainly just need the car running/drivable again so I can get it to my mechanic. Flexible with timing over the next week. Please quote labour only. Also, just a heads up, the car is parked out on the road around the corner from my house. 😊

I would like to install a revering camera to my Hyundai Accent Sport 2018 car. Needs to integrate with existing factory 7-inch screen. Mounting above numberplate centred please.

Needing an auto electrician to install a camera in a car please

I need a car mechanic to replace the battery in my 2019 Kia Sportage with a new one. I don't have any tools so you will need to bring all necessary tools. The new battery will be ready when you come so you just need to provide labour + tools.

3 bikes, fj1200 yamaha, yamaha ag 175 , gpz900r. .the job is to change a plug connection on the fj, Finish applying the wiring loom, a new one oem with diagram. And test inspect stator on the ag 175.

Supply and install to a 2024 Kia Sportage Front and rear dashcam - hardwired Exchange key drive to keyless drive/entry

Replace alternator in Hyundai i30 2009 model. Would need to provide alternator and labour. Rego: 859RZA

Replace alternator in 2013 amarok. Have the new alternator here ready to install.

I have got side steps , brackets and bolts .. needs someone to install it for me

Hi i have a second hand alternator that needs to be installed and the old one taken out. 2006 1.5L toyota yaris. Little information on the alternator. I want it sold before Friday its urgent so only get in touch if you can complete it today or tommorow.

2013 VW Passat Alltrack 2.0TDI having an electrical issue. Multiple codes coming up but the most common being “circuit B low voltage”. Unsure what it is. Car in limp mode but no odd noises. Rough start but I believe that’s because a sensor on the b circuit is faulting due to the larger issue. It happened after another electrician changed the blower unit for the AC. Was driving fine before then. Fairly confident it's going to be an old wire or connector that has gone but I'm not sure how to find it. I've scanned the obd myself to see many codes including P0238 P0322 P0113 The most common is the sensor reference voltage b circuit p0651 and that one has shown up since beginning. That’s all I know. I’m no electrician so I need a good diagnosis if you can :) Please feel free to ask more questions. Thanks

Needing someone to replace headlights on a Mazda 3. Parts supplied. 2010 model

Hey there, I have a 2003 Mercedes Sprinter and I’m currently experiencing some issues with the van’s electrical system. To keep it brief: fuse #7 (under the steering wheel), which is connected to the air circulation system and the horn, kept blowing. I replaced it, but it continued to blow. At one point, I temporarily installed a higher amp fuse so I could start the van as I was stuck in the middle of the desert. The van did start, but the higher amp fuse eventually burned out as well. Once I got home, I identified the issue: a cable near the horn was exposed and touching the bare metal of the van, causing the fuse to blow. I temporarily fixed it with tape, and replaced the fuse with the correct rating. The van now starts fine, and no fuses are blowing anymore. However, I’m now experiencing the following issues: Some lights are dim (likely need replacing) The horn is not working The radio is not working I’m looking for someone who can properly troubleshoot the root cause and help repair/rework the wiring. Here’s what I’d like help with: Properly insulating and redoing the exposed cables (I currently have a temporary tape fix on 3 wires) Repairing the battery cable terminal (the screw for the negative terminal has broken) Diagnosing and fixing the underlying electrical issue Replacing any faulty lights I need this to pass a Roadworthy Certificate (RWC), as the van is currently registered interstate. I have some basic electrical knowledge and am happy to assist if needed. I can also remove the dashboard beforehand to speed things up and allow you to start troubleshooting right away. I’ve attached some photos for reference. I’m quite flexible with timing, and I’d appreciate a fixed quote if possible, as I’m currently on a budget. Of course, I’ll cover the cost of any replacement parts (like lights) separately. I also use Airtasker, so feel free to reach out there or here if you have any questions. Thanks in advance! Michael

I need a round 7 pin plug with a trailer brake replaced with a 12 pin flat plug fitted with an Anderson plug. I have a couple of other things also. Located at Coorparoo or Park Ridge. Price is negotiable.

Installation of hybrid in a bedroom