Hire a trusted car parking sensor replacement service in Brisbane Southside

Looking to have Viofo A329S (front and rear) dash cameras installed in 3 vehicles, hard wired with concealed wiring. I have the 3x A329S, 3x HK6 hard wire kits and one extra 10m cable. Vehicle are 2022 Prado, 2018 Focus and 2012 Hilux Dual-cab. Also want an extra power USB in Prado and reverse camera installed on the Hilux, which I have kits for both.

I need a rearward baby car seat installed

-Reverse camera wiring to be attached to reverse brake light power cable so that reverse camera turns on in car play screen when car is put into reverse gear - carplay kit and wiring already bought, can buy t tap connector if required - mitsubishi lancer 2009 hatchback - please refer to photos

Need my head unit installed i dont trust myself

I bought a new head unit for my ford ranger but i dont trust myself to do it by myself

Looking for an experienced car audio/speaker installer. Vehicle: 2016 Mazda 3 BN Hatchback (Non-Bose) Speaker kit: Kenwood KFC-PS170C (already purchased) Job: Remove the factory front door speakers and dash tweeters. Install the new Kenwood component speakers and crossovers. Test that everything is working correctly after installation. I haven't purchased the required speaker harnesses or mounting brackets yet. If you already have compatible parts available, I'm happy to purchase them from you. Otherwise, please let me know exactly which harnesses and brackets I need, and I'll buy them before the installation. Please only make an offer if you have experience installing aftermarket car audio systems, especially in Mazda vehicles or similar cars. Thank you!

Chasing an experienced dashcam installer to install pictured dashcam in my Nissan Qashqai. All cords needs to be hidden and dashcam set up to app. Ensure cameras are fully operational after install

Installation of a rear dash cam for a Volvo XC40. The dash cam is a Fitcamx. I've already installed the front camera but need help with the rear camera so that the cable is tucked away and not visible.

Install pioneer head unit into 2011 Prado gel

Need a sub and speakers installed

Fit factory nudge bar to nissian navara d40

Reverse osmosis system installation under sink. Take only 1 hour to install if done by a professional.

Price on installation of Andoid carplay already purchased

I have got side steps , brackets and bolts .. needs someone to install it for me

I bought a new reverse osmosis water filter system and I need it installed.

I have a WOLFBOX G850Pro with hardware kit that I would like installed to my BYD Sealion 7. https://au.wolfbox.com/products/wolfbox-g850-rearview-mirror-backup-camera-dash-cam I also have a trunk lighting kit that replaces the existing trunk side lights, so I'd mainly need help installing it around the trims so it looks clean.

Description: I’ve got a set of aftermarket fender flares that need a full professional install on my car. This is not just a basic install — it will likely involve: - Drilling where required - Installing supplied clips (multiple types included) - Properly mounting and aligning the flares Main issue: The rubber edge trim/seal that goes around the flares is not fitting properly. It doesn’t clip on and falls off easily. It appears to be a “7”-shaped trim rather than a standard clip-on type, so it may require the correct method, adhesive, or replacement. Also, the flares are hollow, so only the outer edge contacts the car. I want this done cleanly with the correct approach so it sits flush and doesn’t look messy. What I need: - Someone experienced with body kits / fender flares - Confident with drilling and proper mounting - Able to sort out the rubber trim (fit properly or recommend better solution) - Clean, professional finish Important: - I want this done properly, not a quick temporary fix - You may need to supply or recommend proper adhesive/tape if required I can provide photos or show everything in person. Location: carindale/ carina area Flexible with timing

Just wiring in a car amplifier

I am looking for a qualified Auto Electrician or experienced Dashcam Installer to fit a dual-channel dashcam system (VIOFO) into a 2026 BMW i4 (G26). The goal is a "factory-finish" look with minimal visible wires. Vehicle Details Model: 2026 BMW i4 (Gran Coupe/Liftback). Scope of Work Front Camera: Install using a Mirror Tap / Rain Sensor Y-Harness (hardware provided). Must be tucked neatly within the factory mirror shroud. Rear Camera: Mount to the rear glass. Critical Requirement: The cable must be routed through the existing rubber wiring bellows (boot) between the chassis and the tailgate to ensure it is invisible and protected when the hatch opens. Airbag Safety: All cabling must be routed behind the A-pillar and roof-line side curtain airbags to ensure full safety compliance.

I have the car play unit installed half way but was unable to change the entire reverse camera unit and looking for someone to help me finish the rest and dash camera installation