Find professional window and door services in North West Perth

I have two interior doors that I'm unable to fit independently Needing someone to finish off cutting them properly, cut in the handles and hinges etc and hang them. Painting them would be a huge bonus, but I am able to do this myself at a later date too

Need a carpenter/handyman urgently before new flooring installation on Tuesday. The bottom of an internal door frame has water damage/rot and the door itself is also damaged at the bottom. Looking for someone to: * Remove damaged door from frame * Repair or replace damaged lower section of door jamb/frame * Make area solid and ready for new flooring installation I will organise the replacement door separately afterward.

I want to make this room as bedroom..plz install and supply sliding doors and other concertina door that is cheaper and easy.

I have a small theatre room that is open,i want to use that as second bedroom and therefore need to install sliding door. Concertina Sliding doors from bunnings are cheaper and easy to install. Will need someone to install them. They are $80 each so will need 3 packs. Current measurement are width 1900 and height around 2200. If I buy the product then I expect $130 for installation. Won't take more than an hour. If you supply a customised product then we can negotiate the asking price.

I need to rollers installed they need to be supplied and a new handle installed see photo for handle I have purchased..

2 external wooden doors replaced and repainted.

Sectional Garage Door Service – Menora Hi I’m after a proper service on a sectional garage door at my place in Menora. Just a standard tighten/adjust/lube: hinges rollers roller brackets track brackets opener force + travel check torsion spring lubrication No parts unless you can show me the wear first. Looking for someone experienced (ex long‑time techs welcome). What’s your flat rate for a full service?

I have a kitchen cupboard that needs a hinge replaced it’s completely snapped. It’s a Kaboodle kitchen cupboard from Bunnings

Need door handle fixed

One roller on sliding door is jammed - electric saw will be required to cut through screws. Require 2 x rollers replaced on sliding door (there is a Bunnings on my street, I’ll grab the right size once confirmed) and flywire replaced on 3 x frames - I have the new flywire and tubing ready here to use. Job in Joondanna 6060

Hi I need a door frame supplied and installed for a house in Dianellla. The door supplied for hanging is 81.5cm x 202cm (hinged door). Quote to include frame, plastering at the top, hang existing door and removal of all rubbish. Space for door and frame is 91.5cm (w) x 242.5cm (h, ground to ceiling).

I have a door that needs a weatherproof seal put on the bottom. It may need a little bit shearing off

I trimmed the edge of a door to shorten however the cut is wonky and I need help smoothing or levelling the edge.

Looking for a handyman/carpenter to fit a new door to an old door frame. All materials to be purchased by me need someone with the tools and know-how to install. It is an older house, built in 1978, so the door frame is not exact (see measurements). It will therefore need to be trimmed and planed a fair amount, hence we will be using a Solid Timber Pine Core (STPC) door, which will also need to use wide throw hinges (happy to re-use existing hardware) so the door can swing past the inside wall, + fitment of door hardware handle + latch assembly. Happy for you to come and take a look at the job before undertaking work and purchasing materials. The door will also be very heavy, so I'm more than happy to help with assisting/lifting. Measurements: Door Frame Height: (slight decline left to right) Left = 1990mm Centre = 1985mm Right = 1983mm Width: Top = 815mm Middle = 815mm Bottom = 810mm Depth: 40mm

I have a new internal door that needs to be cut to size and hung. The door will need trimming to fit the existing frame, hinges installed (or transferred from old door), and door hung so it opens and closes properly. Also need hole drilled for handle. Looking for someone experienced with carpentry or door installation. Please bring necessary tools.

Door handle is loose , you will need to bring your own tools … not an expert in this but maybe some screw drivers to tighten it ? Please make sure before requesting an offer you stick to the time and date that we have arranged . If you feel you’re inadequate and have poor organisational skills please do not accept this task. I don’t have time for time wasters !

The door had moved slightly so I can’t close it - it needs slightly realigned maybe 2mm ?

I need a single garage roller door removed (including all side roller panels) and taken away. Located in Trigg.

Need a new flyscreen fitted to our sliding screen door. (Current one torn) Size is approx 200 x 120. It’s a sliding stacker door so mesh needs to match mesh on other door. See photos. Thank you :)

I need a dog door removed from a low light window- the entire pane of glass with the dog door in it, and the original pane of glass put back in (I have that). It’s a rental and I’m moving out so I have to return it to how it was. The job needs to be done between us moving out on the 13th would prefer it done the 17th at the absolute latest. You’ll need your own tools and supplies to put the other windows pane in. It’s small, the door was for Jack Russell’s.