Find local power point installers in NSW

I need to move a power point over approx 12cms on a tiled wall to accommodate a new bathroom cabinet being installed

We need 5 power points installed! 5 pcs of brushed wall plates, as we want the power points hidden behind the wall for each screen on display We have two existing power points which are 10AMP

I have an external power point that I need installed by a licenced electrician. I will supply the materials (external weatherproof power point)

Installation of an outdoor power point for automatic sliding gate next to concrete slab for motor and track which has yet to be poured. I am replacing the driveway so I can get the concreter to run a conduit in preparation for cabling so no trenching is required.

replace power pomit with new one which i already have; mount on the wall bracket to hang vaccum cleaner

The wall surrounding power point gang plate has been pushed in cresting hole. It needs a fix before end of lease! There are two of these.

Hi, Needing an electrician to install 3 power points and run cords through wall to bottom. Also help with installation of TVs on the wall x 3

I’m looking for a licensed electrician to: *Replace two existing power points/sockets *Check and fix an outdoor sensor light that is not working I’m looking for a licensed electrician to:

Looking for a licensed electrician for a few small jobs in one visit: 1. Replace 2 existing wall sconces with new light fittings (new fittings will be supplied) 2. Install a new backlit mirror (power connection required) 3. Fix a double power point – one socket isn’t switching on All fittings/fixtures will be on-site and ready to go. Looking for someone with the right licence/certification who can provide a compliance certificate if needed. Category: Electrical Location: Allambie Heights, NSW 2100 When: Flexible – within the next week Budget: $300

One of our power points has started to crackle when we plug IT items into it. It’s only started recently. So we’ve turned it off and need it checked or replaced.

We're looking for a licensed electrician to install a new power point above our shelving. The cable can be run down from the ceiling cavity directly above, so it should be a straightforward installation. We expect the job to take around an hour, and our budget is approximately $500. Please send through your offers. **Licensed electricians only, please** Thanks!

I need to replace 2 power points and 2 light switches. 1 set is in the bathroom on a tile and the other is in bedroom. I have the replacement parts. Just need to replace them and fit them on the wall/tiles

We are looking for an electrician that can install 6 x power into joinery and 5 power points into plaster wall. All holes are already cut in plaster and joinery. Labour only. Materials are on site. We have installed some new desks into an office and there is existing power from old desks so there is a loop from an existing power point through the joinery already. You will need to. Fit off of power points. Wire 3 loops into existing power points. To liven up. Must have electrical licence. Easy access to job. You can park 10m from the work location. Plenty of parking. No stairs or lifts.

Need a licensed electrician to replace 3 light switches, 3 double power points and 1 bathroom batten light fitting. I have already purchased all the replacement fittings. Please install them and test that everything is working properly. Photos attached

Install the power point at the back of the house when the electrical box is at the front. It needs to include parts and labor.

Screw in 3 light switches 1 power point 1 light

We just need a PowerPoint in our kitchen disconnected. We will be plastering over the top of where the existing power point is so just need someone qualified to do it properly.

Some power points are not working. When checked, one of the RCBs manual tripping function not working.

We are having some modifications done in our Kitchen to install a small cutlery drawer above our microwave oven (as a separate Airtasker Task). However, for that task to go ahead, we need to ensure the Power Point to our Microwave Oven does not clash with the new drawer to be installed. The current Power Point is in the top left hand corner of the enclosure, we require it to be moved downwards by about 100 to 150mm. I think the Power Outlet is surface mounted to the back of the enclosure, and from what I can tell, the power cable comes into it from the cabinet wall on the left hand side, which is the sink enclosure.

Looking for an electrician to complete a small residential job in my apartment. The apartment was built around 2000, so the wiring is relatively modern and I don’t anticipate any major issues. Work required: Light switches and power points + two LED lights replaced, includes - * Replace 11 × double power points * Replace 1 × quad power point * Replace 6 × single light switches * Replace 1 × two gang light switch * Install 2 × two gang LED dimmer/switch combinations * Might need 1 × surface mounting block (bathroom) * Install 2 × new Martec Fino LED ceiling lights, replacing two existing LED ceiling lights (same locations, pretty much the same lights just a bit bigger, no new wiring required ect) I will supply everything, it’s Clipsal Iconic and I think the old ones are HMP: * Clipsal Iconic switches and power points * Martec Fino LED lights * Dimmers * Mounting block I’m looking for: * Licensed and insured electrician * Neat, professional installation * Experience installing Clipsal Iconic products and LED dimmers Preferred, not necessary though Photos of the existing switches, power points and lights can be provided if needed