Find professional metal gate repairs near you

Spray Painting – Metal Gate Glossy White Finish Looking for an experienced to spray paint a metal gate in glossy white. 📍 Located in my garage/backyard 📏 Measurements are shown in the attached photos. Requirements: * Glossy white finish * Suitable for outdoor use and local weather * Clean/degrease the metal thoroughly with mineral spirits first * Apply a suitable metal prep primer/base coat * Finish with a durable epoxy topcoat * All preparation and materials to be included Please provide a fixed total price including ALL materials and labour. No additional/extras costs after accepting the job.

I need a handyman to fix a metal gate, maybe some parts missing and clean the paint of the pavers maybe pressure wash

Metal gate with lox mechanism (which you can open from a panel inside the house) is not latching. The gate is affixed to concrete besser brick walls either side which have likely moved meaning it wont latch. i have tried to adjust and move the plate it still wont latch.

Looking for someone to repair our metal front gate. One of the welded joints has come apart and the metal section has detached. Would like it reattached securely and restored to its original position. Please see photos. Ideally looking for someone experienced with metal gate repairs/welding.

I have garden metal gate that is attached with 2 screws need removed

Need to reattach metal (iron) gate to wooden post, and provide a latch for the other side. Gate is 2x1m. The gate came off in the wind.

I have a metal gate which has rusted at the bottom. I’d like the rusty bottom bar cut out and a new piece welded in. The gate has a curve to it as well.

Looking for a handyman to refit a small decorative metal gate( red gate as in pic)that’s come loose from its groove. The gate needs to be reattached securely to the brick wall ideally using a bracket or clamp setup similar to the example shown in the green gate photo.Expecting the handyman to - Inspect current gate alignment and mounting points. Supply and install suitable brackets or clamps.Ensure gate is level, secure and functional

Removing old gate latches from metal gates in Richmond (you have repaired hinges on same gate before), need to repair existing holes in preparation for new handle/latch and hook

The metal post for our side gate has come away from the external wall and needs to be securely reattached, as shown in the photos. The mounting holes have already been drilled. The wall has an external wall insulation system (EWIS), so the appropriate plugs, fixings or chemical anchors must be used to secure the post properly without damaging the wall. Please supply all necessary fixings/materials and seal the penetrations so they remain weatherproof. Looking for someone experienced with mounting into externally insulated/rendered walls. The gate and metal post are otherwise intact. Anytime this week please. Location Robina, 4226

One of the upper hinges on our metal driveway gate has broken away from the gate frame and needs to be repaired/re-welded. The lower hinge is still intact, and the gate is currently closed and secured with ground bolts. The gate is not used frequently, but we rent out the parking space behind it, so safety and long-term stability are important. Looking for someone experienced with metal gate repairs / welding to: • Repair and securely re-weld the broken upper hinge • Add reinforcement if needed for a strong and durable repair • Check the other three hinges and gate posts for any cracking, corrosion or signs of fatigue • Let me know if any other preventative reinforcement is recommended The gate opens outward and there is good access from the driveway. A vehicle is currently parked behind the gate, but it should not interfere with the repair. Please bring your own welding equipment and tools. Photos attached. Please let me know your proposed repair approach and estimated cost based on the photos. Ideally looking to have this repaired by Wednesday 23 September.

A top handing metal gate is off the rail, need to get a part to slide it back to the rail

Gate needs to be level & lockable. You will need to supply necessary brackets to mount gate. It may require a second post to position gate in connect location.

Two old metal gates 2.6 metres long and 1.4 metres high need to be cut into smaller bits to then go into hard waste. Each gate cut into three Would need a grinder or perhaps saw with special metal blade Easy access as in garage undercover

Replace metal gate with new metal gate. Have new gate and fittings already.

Looking for someone to help as a gate has come off the brick wall. Its originally been bolted into the mortar and the bottom bracket has come out, and the top ones rusted. Looking for a quote for someone to fix it and what they would do to fix it as well.

My metal gate has stopped closing due to erosion/wear on the latch area. The latch no longer lines up or catches properly, and the gate can’t be secured. I need someone who can assess the damage, realign or rebuild the latch mechanism, and ensure the gate closes smoothly and safely again.

The metal frame of a colour bond gate needs repair. Likely need to be welded. Gate does not close/latch properly. In the winds last night the gate has come open a ripped off the already loose latch on the bottom of the gate. As the top latch also does not reach at all and need to be fixed. The quote here is notional and extra costs can be added later.

I have a metal front gate. The hinge has rusted out/failed. I purchased additional hinges from Bunnings, but I don’t think the holes accurately line up for the screws. Will need someone that is able to fix/reattach. Photo is what it looks like properly attached.

I have a metal side gate where the latch/bolt goes into a brick wall. The brick has worn out and been patched previously and the bolt can now be forced out, wearing away the brick. I need a proper, long-lasting fix. I believe we need to drill into the brick and install a steel receiver/sleeve (tube) for the bolt or something similar to fix the issue. Open to other ideas!