Find an experienced handyman in Springwood QLD

Hi, I have a swing installed on my back yard but hasn’t attached to the ground yet, not sure how to do it even with the instruction sheet. I really Need someone who can fix the step. Please refer to the pictures. Thanks. need Please refer to my pictures.

I need a handyman that can drill some holes to install diy blinds

Repair 3 holes in bedroom. Also paint.

Office rooms , 8 , need Sound Proof Panels installed

Sorry if the image is hard to see it’s the best I could do! As title says I am in need of Someone to repair my bathroom vanity it has one hair straighter mark thanks !

Wall section to reinstate is 3.5m long x 1.3m high. The plasterboard was removed from a brick/masonry wall. The wall-to-slab joint at the base has been pressure-injected with waterproofing membrane. The brick face has been coated with membrane paint. The area is now dry and stable. Scope required: Reinstate the wall to the original finished line. Do not bring the wall forward or box it out. The original plasterboard sat about 25mm off the brick. Install a low-profile fixing support (thin battens or furring channels) fixed to the masonry where appropriate. No drilling or fixings through the injected waterproofed base joint at the slab. Keep the bottom edge of the new sheet 10 to 15mm above the slab so it does not touch the floor. If any mechanical fixings must go through the membrane-painted brick, each fixing point must be sealed so the waterproofing remains continuous. This means sealant in the drilled hole before the fixing goes in, seal around the head, then touch up with membrane paint. Supply and install moisture resistant plasterboard. If you recommend fibre cement instead, please explain why. Tape and set joints, then sand to a paint-ready finish. Clean up and remove all rubbish. Quoting: Please include materials and labour. Please confirm your proposed fixing method. I do not want an adhesive-only dot-and-dab plasterboard install directly onto the membrane-painted brick.

Replace standard ceiling fan. I will provide fan

Install a new door and it’s hardware

I'm looking for a friendly, capable handyman to help with a small job first, with the goal of potentially retaining you for more odd jobs around the house. Initial Task: Fix/replace a broken hinge on a small side gate (garage entrance) Future Jobs (if happy with your work): Replace interior door knobs Adjust minor fittings or cabinet doors Basic maintenance and odd jobs around the house What I'm Looking For: Someone who works efficiently and with care Hourly rate preferred for future jobs Open to discussing further work The listed price is just for this first small job and inspection. I'm happy to work out additional scope and payment privately if this job goes well.

Need gutters fixed or replaced

Hi just need some help with some things around the house: - putting up blinds and curtains - building outdoor shed (flat pack sort of system) - garbage removal - plastering roof and holes Other little things around house :)

Repair hole in bedroom wall

I need someone to fix my kitchen water tap, please look at the picture

I need to install a DC ceiling fan

Also, the drawers need re-wrapping if that’s a thing. Sorry, I don’t have a photo of that.

Needing mobile rim repair for same day fix on 1 alloy wheel. Light gutter scrape.

Needing to take out old vanity and install new one Mount in place and silicone in 900mm vanity

Hi, I need a few handyman (or person) tasks done at home. I need: - Back door adjusted so that it closes properly. It doesn't latch properly when closed, and needs a shove each time. - A bedroom door that is similar. - A downpipe that needs redirecting or capping off. - A toilet roll holder that needs attaching to the wall. There's other tasks that I could find too, so happy to pay by the hour for work done.

Would like 3 ceiling fans installed in my townhouse. 2 downstairs and 1 in the master bedroom. Replacing existing light fittings downstairs and fan in master.

weathered plastic line on a rotary clothes line needs replacing and strung with durable galvanised coil. Must be able to achieve good tension. No sag