Find a professional gyprocker contractor in Sydney Eastern Suburbs

Supply and instal all materials Includes gyprock to stud wall 1800 long and 2650mm high . Instal gyprock , angles, set and cornice I can provide also provide free labour for a few hours

Hi guys, we need an internal demo / strip-out at our shop. Please only offer if you can do everything below and leave the site clean. Scope (all included): Demolish and remove 2 non-structural gyprock walls, including timber studs/frame inside Remove all rubbish off-site (gyprock + timber + fixings) — tip fees included Leave the area completely clean (sweep + vacuum) — floor must be spotless, and be careful with the ceiling. Wall sizes: Wall 1: 3.9m W x 3.0m H Wall 2: 2.55m W x 3.0m H Timing: High urgency — tonight (after-hours) is ideal, otherwise ASAP. Requirements: Experience with internal demo/gyprock removal Bring your own tools + protection (drop sheets, dust control, etc.) Must be able to handle disposal + cleanup ---- There is a timber workshop floor/platform we’re removing as part of opening up the showroom. We need the timber to be cut back in a straight line (even/flush edge) so it looks neat and is ready for finishing. After the cut, we need a small ramp/transition installed along the edge to eliminate any trip hazard (safe, tidy, durable). The ramp/transition should be securely fixed and suitable for a retail environment (people walking through all day). Timber workshop floor cut + safe finish We have a timber floor section that needs to be cut straight / even (flush finish) to suit the new open showroom layout Install a small ramp / transition strip to avoid trip hazards (safe, neat finish) Prefer insured (public liability) / professional When offering, please confirm: You understand this is all-inclusive fixed price (demo + disposal + full clean) You can do it after-hours if needed Photos attached.

Build bulkhead 40cm x 4.6m and 50cm x 2.83m Encase electrical fuse box in corner position (110cm x 60cm) Encase pipe 1.8m x 15cm x 15cm

Want to create a room by closing off an area with two gyprock walls with a door frame

Pretty simple job. Supply and fit one x or cut two x gyprock sheet/s to masonry wall no battens required as it will be a snug fit. No patching, no painting required. I have 1 x small tub of glue. Sheets can be fixed vertically or horizontally. 2625 x 1360mm h (1350 h ok)

3 bedrooms walls needs small patching after removing 3 aircon units . I will paint myself. Removal of a Gyprock piece in lounge room as per photos . Due to water damage (now fixed ) a 1-1 1/2 metre vertical crack appeared in Gyprock . It has been filled with no more gaps but needs fixed professionally l please . Will paint myself . I don’t know the cost so have just put $100 in budget . know it’s more but you tell me what the qoute would be please . Thank you

Description Need gyprock repaired and painted to match existing. Wall Repair damaged gyprock around power point and wall above, including replacing missing section, tape, set, sand, prime and paint. Power point faceplate to be removed and refitted safely. Ceiling Repair hole and crack line, tape, set, sand, prime stain block if needed and paint ceiling to blend.

Gyprock to be installed in opening for a door to be installed. Door, handle and hinges already purchased.

I have a 15cm x 15cm approx corner of ceiling that needs to be cut out and re patched with gyprock and then sanded and a coat of paint, to make it tie in again with the rest of the ceiling .

I need my Samsung frame flatscreen hung on the wall today I do not have a bracket

Hi, need a licensed tradesperson (plasterer or passive fire specialist) for a small but compliance-critical ceiling repair in my top-floor (3rd storey) strata unit in Bondi Junction, NSW. Job details: • Patch and fireproof a single 150 mm hole in a double-layer Gyprock fire-rated ceiling. It’s to cover a hole made for range hood ductwork that is going to be removed. • Access via manhole to roof cavity from inside unit (no external roof access needed). • Must restore full fire-resistance level (FRL) per Australian Standards (AS 1530.4/NCC) using tested passive fire system + matching plasterboard reinstatement on underside. • Include photos, product data sheets, and compliance statement for strata AFSS. • No cosmetic finish required (just functional patch); I’ll paint later. Requirements: • Experience with strata fire-rated repairs (double Gyprock ceilings). • Provide tested system detail for this penetration size. • Public liability insurance + relevant certifications. Budget: (open to quotes based on method). Please reply with your experience, proposed approach, and fixed price quote.

Plasterboard wall repair after TV mount removal – professional finish required. I have a wall with multiple old TV mount holes, metal anchors, and a cable chase opening. I need: • All metal anchors removed • Damaged plasterboard cut back cleanly • New plasterboard patches installed with backing • Joints taped, skim coated, sanded flat • Entire wall repainted to match existing finish This is not a filler-only job — it must be done properly so the wall is perfectly flat and invisible after painting. I also want all cables hidden behind the wall Please quote including materials and paint.

I need a smooth finally in my ceiling, remplace a little 1 x 1,5 mts of gyprock and repair crack

Paint over a small 1m diameter gyprock patch-up, ceiling (paint, roller, stirrer and tray supplied). Need done today please. Have sanded already.

Need to remove Gyprock part and make some more space.( its possible, checked back side). Need more room for bigger fridge.

Have recently repaired a roof leak and now need one sheet of gyprock replaced. The opening itself is about 600x400mm but would prefer a 2400x1200mm replacement.

Instructions: 1) patch hole on ceiling with gyprock 2) cut out section of return air box to allow air flow into the unit 3) cut in and install 45x45 man hole into patched section to allow for access to the unit in future if required

Hi. I need a handyman to fix a small hole (maybe 7-10cm big) in gyprock. Can you please give me a quote? Ideally, I’d like this done tomorrow but I am flexible (this weekend is good too). Thanks! I also need someone able to light sand and paint.

Need signage on the lift glass, Door and gyprock wall going upstairs And on a glass top of door