Find a fence installation professional in Mornington Peninsula

We need to install a side gate in our house. 1. It needs to be automated/remote controlled 2. The width is 3.2 meters 3. The gate must swing against the RHS of the photo against the brick 4. We prefer the gate to be made of Colourbond, red to match the bricks would be preferrable, although happy to consider other colours Please see the photos for more details

I need a new gate at the foot of 5 steps that lead from the carport to the entrance to the house because I have a bolter of a dog . One on the left shows what I’m using now - two dog cage panels. On the right is a safety fence panel turned on its side which is about the right size I think . Certainly no pool lock needed just a latch but if it’s not suitable (too heavy maybe ) I’ll need a new gate in that style.

Looking for someone to arrange and install a 3.5m glass pool fence with a door in the middle. I have a section on a balcony that I’d like to enclose, 3.5m wide. Assuming can be achieved with: 2 x 1250 side panels 1 x 900 for the door + Spigots, hinges etc https://www.bunnings.com.au/protectoral-1250-x-1200-x-12mm-glass-pool-panel_p0389566 https://www.bunnings.com.au/protectoral-95-x-95-x-162mm-stainless-steel-glass-fence-chisel-spigot-2-pack_p0038898 Looking for a full quote please for the parts supplied and install for the 3.5m gate, preferably installed by next week in Arthurs Seat 3936. Thank you

We want to build a fence in our backyard. The fence can either be a brush fence (photo in attached) or a regular external backyard fence. Which would be cheaper? We would also was a gate installed seamlessly too. Looking at our lease line, we will need to remove a whole lot of trees as well, so please quote on removal of them as a seperate cost. The dimensions of the fence would be: 23m + 4m + 8m + 4m. 2m high I wonder if you could use the posts already installed, or best to start again?

I have 11 lengths (2.4m each) of trellis that I need installed on top of my timber side fences. Job needs to be done before the end of the week.

Install cement sheeting on fence panel

We are planning to take out a cyclone fence this weekend and want to replace it with a 2.3-2.4 M timber pailing fence-- we had planned to do this ourselves, but if there's a local carpenter/fencer, we would hire. 10.5 M length. Best side facing inward. See attached images, one with pailing (simple style), one batten (more $$?), ideally a quote on both to compare pricing. Thank you.

Replace 100 x 100 fence post which is partially set in concrete. Owner can prep the work area including removing (and replacing) attached gate and fence. New post setting requires busting out old base concrete, digging post hole .5 metre deep, setting in concrete. Must be very careful not to damage copper water line (photo - red mark left side of hole) within 12 cm of post base.

Needing someone to supply and install temporary fencing. Approx 30lm required. Approx 8 weeks hire.

Moving into a new house and require new boundary fencing thought the rear and sides of house. Full fence on rear = 51m Rear yard left side = 27m Rear yard right side = 27m Considerable amount of trees present. Pretty flat block. Currently there is small mesh wire fence to remove.

I require a quote and installation of a front fence between two properties. I’m after the black metal fence

I clipped the post with my ute and it’s ripped a section out of the face. It’s not load-bearing since the gate is sliding, so I’m after a clean repair—either cutting in a new piece or rebuilding the section—and matching the paint so it blends in properly.

Need two opening gates installed and one post

Demolish existing fence and build new timber paling fence 2m tall approx 14m wide of area shown in red line

Need a broken gate latch replaced

Need some wood put on these two gates looking for a quote please

I need someone to install and adjust a side gate that has been moved from its original location to a new, narrower space (approximately 30 cm narrower). One of the two side posts has already been installed and concreted into the ground. The gate is probably the same of the Adjustable Steel Gate Frame Kit sold from Bunnings, is meant to be cut to size and doesn't require to be welded after, just screwed. The job involves: - Installing the second post onto a brick wall - Fitting the hinges onto the posts - Cutting/adjusting the two gate doors so they fit the new opening (roughly 15 cm each door). - Hanging the gates on the posts - Ensuring the doors align properly and close smoothly You will need your own tools to cut and fit the gate and experience with gate or fence installation. Additionally, we may also be interested in prepping and staining the gate, depending on cost. I’m not sure about the cost for this job, so please make an offer with what you consider a fair price. Thank you.

We need a compliant pool gate, exactly like the one shown in the first image. The last two pics are where it needs to go. Approx 148cm. Any questions please let me know! $$ is only for labor and will pay extra for material.

I need two picket fence panels built. One 3100mm wide and the other 4000mm wide. The posts are already in place. We will supply the pickets. You would need to supply the railings. The existing panel you can see in the photos is just leaning there and will be removed.

I need a gate made and installed including lock and mesh screen