Find trusted local electricians in Toongabbie NSW

The power point board has broken off the wall. The wires are still in tact. I have a solar battery so that needs to be turned off correctly to make sure no power when replacing the board

I have installed a solar batteries system, and it's working with the main house appliances and show the load, however I don't think it's connected to all the appliances such as air-con in the living room or granny flat sub board, because when those appliances are running, it doesn't show in the solar battery app. - my house is a 2 x 1-phase meter, 1 for any time use, 1 for controlled load with hot water - the sub board doesn't have meter, it only have switchers - my solar panel is 8.8kw and battery is 32kwh, it should be enough for all appliances - the meter board has been upgraded recently, no risk of asbestos Need: Electrician to inspect the CT clamp installation and ensure all circuits are being monitored correctly. Likely need additional CT clamps installed or existing ones repositioned to capture loads from all circuits including the air con and granny flat sub-board.

I need to install Ceiling Fan in living room and 2 bed rooms - Total (3) Down lights to be installed in 2 bed rooms ( total 8 down lights) Remove exisiting light in room

Need to replace 3 old electrical switch plates woth new ones that I have.

Hi, I’m looking for an experienced and reliable tradie (or team) to finish my garage. Work includes installing gyprock, insulation, plastering ready for paint, installing 7 downlights, and cladding the outside uper section with cement board. Garage Size & Details: Length: 6m Width: 4m Ceiling height: 2.8m (front) and 2.6m (back) Need gyprock installed on walls & ceiling Need insulation installed before gyprock Need full plastering / setting done (ready to paint) Need 7x LED downlights installed (wiring run & lights fitted) Outside wall: need cement sheet/blueboard installed – 40cm height × 16m length Please include in your quote: Labour cost All tools and fixings If you can supply materials (optional) please note it in your quote Estimated timeframe to complete the job Your experience or photos of similar jobs Location: Toongabbie NSW Looking for: Someone skilled, punctual, and with solid gyprock + electrical installation experience. Must ensure a clean and neat finish.

Need to install Domus floodlight. I will buy the light itself. You will need to provide all tools and wiring.

The downlight in my bathroom is flickering Not sure if the bulb needs to be changed or if it’s something to do with the wiring

I am building a granny flat and need to uninstall 16 solar panels from the garage. I’ll need the panels reinstalled in the future. Please provide a quote for uninstallation only. Please quote only if you have prior experience of solar panel uninstallation.

Replace down light bulbs. You need to bring the bulbs. Will reimburse bulb cost. Need to replace 2 bulbs

Samsung AI smart GEO wind free purification split system 2.5kw installation

Uninstall and install solar panels

Hi, I’m looking for a licensed electrician to help with a few small jobs around my house: Connect and install a new outdoor sensor light at the front of the house .

light fitting needs new replacement also install a batten alabaster light shade and pin b 22 led bulb we already purchased. ceiling 9ft. only qualified licenced electrician please. must remove existing, provide the light fitting itself and install it with our shade and bulb

Please see the picture for details regarding location of AC unit. Looking for someone to install (licensed) Split AC . Model: hisense c5.0kw h6.4kw reverse cycle split system hawv18kr Bought from Good Guys. House: Single Storey Pls offer your best/lowest price to get the job done.

Need to unblock the sink,supply and change a tap ,new lights ,switches to be supplied and installed ,the budget I put in is for both electrical and plumbing works.

Task 1: Need to fix 3 broken electric switches? Task 2: Need to check all switches and replace if any of these are about to be broken soon? Note, its a 3bed 2 bath unit.

I have a Bosch gas water heater. At times there is no hot water coming, even when left on for more then 5 minutes. But when i unplug the system and replug after 10 mins it starts working. Might need replacement please provide a total quote with material thanks.

Power point to be installed for Gate motor. I am getting FAAC 720C motor installed for sliding gate motor. 1. Need to install a power point ( I will provide the outdoor power point) near the mains. Mains is on left hand side of the house when facing the house 2. need to install power point (you will provide) near the sliding gate for motor from the mains power point.

Need to install a split aircon. 2.5 to 3kW recycle unit both cooling and heating. balcony near the bedroom. max copper pipe will be around 8m. In photo, the wiring shall be top of false ceiling or do a concealing box but need to check the door opening.

I need a light fixture (already supplied) installed where a ceiling fan used to be.