Find experienced local carpenters in Newcastle

Hi Looking for someone to supply and install hardiplanks wood grain on a outside wall, It’s 2.5 metres high and 2.15 in width . The frame is in place with a vapour barrier so it’s ready to be installed , quote is for install only the materials will be added on top

I required handmay in Gloucester Saleyards, Cemetery Rd, Gloucester NSW 2422.I will pay the all travel cost. Handyman Needed For The Following Minor Repairs. 1) Reattach Cupboard Door 2) Reattach Architrave Where It Is Falling Off. Some other tasks could be also found on site after visiting.There are no pictures available and the site can be visited.

$300 - 30 mins work - requires on-site at Newcastle Knights stadium at 10am Saturday (tomorrow) Very basic carpentry requires. Replace one aluminium panel with a new one to a wooden ground level frame. Basically removing 8 screws and replacing a panel and replacing with new panel. Must be done at 10am for home game in the afternoon. Team member on site to instruct.

Pick up materials Bunnings Wallsend and deliver materials to mayfield . 4 sheets form ply 1200x2400 17mm 5 sheets mdf 1200x2400 3mm

Im looking for someone that can work with metal particularly metal hammering as a door feature for cabinet. As seen in this pick

Need a tradie with tools and who has worked with Kaboodle Kitchen cabinets to help remove a set and put in the new set. Current is under a bench top and may have been liquid nailed. Will need to bring all tools to take it apart. New draws and cupboards have already been constructed just need installation. Edit: there maybe some measuring and cutting of kickboards etc

Assembly new Garden Shed on Concrete pad 3mx2.24m

Hi, I am looking for someone with some experience in doing epoxy flooring. I believe the floor is about 25m2. I am thinking of using a kit for this, will not be spending 2K to get it professionally done. I am also keen on hearing recommendations for a kit.

I need a custom cupboard made for a hallway and some shelved added underneath a bunk bed please. Thank you

We got red wine on the pool table and we need to stain out ASAP!

Need to put the cubby on concrete supports (pier screws and cement need to be purchased for this). Also need to bolt one end of the swings bar to the shed. The photo on the picture is how the cubby looked before being dismantled.

Easy Shed 3m x 1.5m Fixed to concrete slab in backyard

We need old cabinets to be removed and few cabinets to be installed . The cabinets have been purchased and assembled . Also require cutting and installing benchtops and removal of rubbish . Side 1: 900mm cabinet. 2m bench top and a panel for washing machine Side 2: 1000mm cabinet , 1.2 m bench top

I have a nice wooden side table which needs to have the ends trimmed, sawn off and polished up well, so that it can fit into the space I need it to fit in

Build a basic sub floor access door flap for under the house. I don’t have timber material on site but there’s existing hinges and latch. Size is 730 x 900.

We have some shelves we would like put up, along with reinforcing a couple of floating shelves. - 4 shelves that need to be reinforced (I have brackets) - 3 small corner shelves, to be installed - 6 small shelves, to be installed - 2 guitar hooks, to be installed Into Gyprock. Shelves came with the usual nuts and bolts but may need additional support.

Photos attached of the sizes of each space. Need bulkheads built front the top of the cabinetry to the ceiling. Don't have any of the materials required.

Dismantle custom timber bench seat and frame. Removal and disposal of materials. 3m x 1.81m

I’m seeking to remove a kitchen cabinet so we can install a dishwasher. Need the cabinetry removed (I think some cabinetry like bottom panel will need cutting) and need a hole cut in the side of the remaining cabinetry for the dishwasher cables to go through to the next cabinet over under the sink. I have measured and it appears that removing the cabinet will leave the 60cm required for dishwasher. It would be great if cabinetry could also be taken away after job.

We are having glued down hybrid flooring installed. This will raise the floor height and the front door will need to be planed/sanded to ensure it can open and close freely.