Find experienced local carpenters in North West Melbourne

I need a carpenter to make me a wooden fish tank rack for my 2 6ft x2ftx2ft fish tanks that can hold 1000kg per rack.

Lift the cuboards to make room for the TV

Would like to enclose carport. Would like to compare cost of bricks vs framing and plasterboard. Please provide rough quote for 2 x approx 2400w x 2300h.

I have a full length kitchen cabinet. But almost 40% of it is taken up by the HVAC air intake vent. Check photos. The air intake vent is now non-operational and I want to reclaim that unused space. Job- to remove air intake vent panels and install new full size shelves.

Rotting wood on bottom corner of window

- existing pine floorboards, with dated top coat. I want sanded and refinished with a water based matte clear coat afterwards. Home is approx 72m2 internally.

Replace 2x bathroom mirrors (incl disposal) with purchased bathroom cabinets (including building)

1. Clear deck of large furniture and large pots 2. Clean deck with soap and brush off debris 3. Prepare surface, sand paper if required 3. Oil stained deck. Triple coat

We need a Carpenter. Preferably with tools. Please bid with your hourly rate.

We recently had our house relevelled and restumped and need an experienced carpenter to: • Adjust up to three doors affected by the releveling • Check and adjust the hinges and alignment before planing the doors where necessary • Adjust the latches and strike plates if required • Re-secure the separated door trims/architraves • Repair the loose trim beside the front door • Reattach the loose skirting and replace the small broken section The house is currently vacant. Please include labour and basic materials in your offer.

I am looking for an experienced carpenter or door installer to carefully hang and fit an existing solid timber front door in Macedon, VIC. The door has an existing timber frame and sidelights. I have purchased the hardware, including: • Raven RP81 automatic door-bottom seal, 820 mm • Three heavy-duty hinges • Roller lock / catch and strike plate • Electronic deadbolt and strike/keeper Work required • Inspect the existing door, jamb and current hardware positions. • Carefully adjust/plane the door only if required, so it has even gaps and closes freely. • Mark out, mortise and fit three hinges accurately to the door and jamb. • Hang the door and ensure it opens, closes and latches smoothly. • Rout/rebate the bottom of the door to fit the supplied Raven RP81 automatic door-bottom seal. • Install and adjust the door-bottom seal so it drops correctly against the threshold when the door closes. • Fit and align the roller latch/catch and strike plate. • Fit and align the supplied electronic deadbolt and strike/keeper. • Test all hardware and confirm the door operates properly. Important This is a first-fit installation. Once the door and all hardware are correctly fitted and tested, I will remove the door myself for painting/finishing, then reinstall it using the established hinge and hardware positions. I need someone careful and experienced with solid timber exterior doors, hinge mortises, routing/rebates, locks and accurate alignment. I do not want excessive trimming or rough/oversized cut-outs. I will provide the door and all main hardware shown in the photos. Please bring suitable door-hanging, routing/mortising, drilling and fitting tools, plus any required consumables or minor fixings. Please include relevant experience, reviews or photos of similar timber-door and lock-fitting work in your offer. Location: Macedon, VIC Timing: Flexible by arrangement

Remove and replace timber balustrades on front porch, then paint. 5m x 2m. Also replace two front timber steps.

Kitchen cabinet 2x hinges have come off . See photos for details

I need a benchtop installed in my small laundry. I removed the laundry sink to create space for a side-by-side dryer and washer, and now I need a counter or bench to complete the setup. I’ve included some pictures of my laundry and general inspiration. The benchtop will need structural support as I’ll be placing heavy items on it often. I’ll provide the materials.

Replace of kitchen bench and cabinets- supply and install.

Need a handyman to modify/cut down the overhead cabinet above my gas cooktop so a new rangehood can be installed at the required compliant height. Ideally looking to alter only the single cabinet rather than replace all the overhead cabinets. Then install the range hood I have purchased

I’m looking for an experienced handyman, carpenter or cabinet installer to repair and reinforce a floating timber shelf in my home. The shelf has started pulling away from the wall after supporting bottles of alcohol. It appears the adhesive or existing fixing has failed, and I don’t want it simply glued back into place. I’m looking for someone who can: * Inspect the existing installation. * Properly secure and reinforce the shelf using the most suitable method (e.g. concealed brackets, additional fixings, or another long-term solution). * Ensure the shelf is level and capable of safely supporting the weight of alcohol bottles and glassware. * Supply any required fixings/materials (please advise if there will be any additional material costs). I’ve attached photos showing the gap between the shelf and the wall. Please let me know: * Your experience with similar repairs. * How you would likely repair/reinforce it. * Whether your quote includes materials.

We have a large wooden wardrobe which we need to remove intact from wall in order to replace carpet in the room (currently sitting on top of old carpet). Wood strips on either side can be removed/replaced. May require 2 people We would like to ultimately keep this wardrobe, so a no damage removal is needed. It seems to be anchored to wall with some screws, but may require an onsite inspection first to work out next steps. Budget starting point- Please quote for cost to detach and move away from wall so the wall area can be cleaned/carpet removed. Needs to be done tomorrow (Wednesday) before painters come in.

As per photos written quote required from qualified carpenter for the work as mentioned in photos for Insurance

Carport timber post is rotting and needs a repair. It is Load bearing and has colorBond sheet on its roof. The post is 211 cms tall and 10cms thick and the fascia board is 4.6 metres long and 4.7 cms thick and 25cm wide. Please accept the quote and we can discuss in person.