Book a professional blind repair service in Gold Coast

See attached photo to best describe the issue. To fix it, we prefer if it can be repaired by re-stitching/re-attaching the side zip edge rather than replacing the entire panels.

Removal and disposal of existing curtains and curtain rails, followed by the installation of new Venetian blinds. The blinds are to be recessed within the existing window frames and securely fixed into the masonry block walls.

Remove vertical blinds and install 4 s-fold curtain tracks, and one roller blind. The tracks are on the ceiling behind a pelmet.

Need to reconnect power to motorised internal blinds

Need freedom blinds installed , 6x rooms

Looking for a handyman to install 3 brand-new KOO Regent blockout roller blinds. * Each blind measures 180 cm wide × 240 cm drop. * All 3 blinds are being installed into timber. * Existing blinds will already be removed. * New blinds and brackets supplied. * Installer to bring drill, tools and any additional screws required. * Ensure all blinds are level, secure and working correctly.

Remove 3 roller blinds from windows and replace with new ones. Must have own drill and experience doing this task.

Looking for someone experienced with masonry/concrete fixing to install 3 Coolaroo crank-operated outdoor blinds on an apartment balcony. Blinds are: * 2 x 2.4m wide * 1 x 3.0m wide Installation is into the concrete ceiling/soffit. Access is straightforward from the balcony and no working at heights equipment should be required. Would require proper plugs and screws given wind affected area The two 2.4m blinds are going side-by-side across an opening that is approximately 4.8m overall. With the end brackets/fittings, the combined width appears to be closer to 4.94m, so I suspect the blind rode may need to be carefully trimmed/cut down slightly to fit correctly. Need someone who: * Has their own rotary hammer/masonry drill and concrete fixings * Is confident accurately measuring and installing the brackets * Can assess whether the two 2.4m blinds can/should be shortened and carry this out if required * Can install all three blinds level, secure and operating properly * Ideally has experience installing outdoor blinds/awnings into concrete All blinds are onsite and ready to go.

Vertical blinds track need to screw in. Came off from the roof. The hole is big now. Need to move 2-3 cm and rescrew it with heavy duty anchor. 5-10 mins job if you got the right tools with you.

Spring loaded roller blind needs tensioning and perhaps replacing the chain and hung back on the door which is 2400 mm wide x2130mm drop. ATM it’s hard to pull up the chain, it feels like it’s going to snap. Normally it’s so easy to pull up. Going down it’s not a problem. The person who wants this job must be experienced in installing roller blinds. NB we bought a fixing kit if you need to replace the chain and it’s housing, etc

Wanting to put temporary outdoor window blinds on 4 of our 2nd story widows on townhouse. We are renting and in very thin budget. Any help or guidance much appreciated.

Blinds needed here see pic

Install 4 customer-supplied interior roller blinds" my budget is $200

Task 1. I have one single panel roller blind which needs the frame or bracket reattaching back onto the wall. Existing screws have failed and the blind bracket and blind dropped to ground. Task 2. Replace the roller blind chain as old one is broken. Will need a drill and supplies the chain kit itself will be in the unit.

Install roller blinds in underside of window reveal. 6 windows total. Blinds supplied.

Install 3 x roller blinds

Shower blind has come off the latch and a screw has come out. It needs to be re attached. Also need to check the other 2 screws to make sure they are secure.

Install 3 x 180cm roller blinds in our property. We have already removed the old ones.

I have two internal bi-fold plantation blinds I want removed. Both have four panels each and open in the middle (i.e 2 panels each side). They are: 1475mm x 1320mm and 2070mm x 1150mm.