Find a professional bed repair in Melbourne

I have a large bed head that has 2 buttons which have popped off and need to be re-installed

My bed legs on bed frame have given up, I have one leg that is down and currently using a suitcase to level it. I need someone to add additional support blocks and bolt them in. I also need to secure the headboard because that’s wobbly too.

The hinges of the door keeps coming off as the place where the screws go in is now very loose

My bed frame is bent in between I took the apartment on lease on and I knew about it after I took the apartment I need to fix it and any easy solutions are welcomed

The wooden base of this bed is dipping in the middle, needs structural support in the middle.

My bed head is/was mounted on the wall and seems to be falling out the socket. In need of someone to come and repair it, including buying new screw/wall mount hooks and I assume puttying the broken wall. I have a dust allergy so ideally someone who can be careful and clean up well.

Repair 3 stripped screw holes on bed legs. One side of a towel rack needs fixing to the bathroom wall. (I suspect the whole is stripped or damaged as screwing the rack in place doesn't really do anything. It just keeps turning).

Remove the patches of araldile glue which has gone hard on the top of a bedside table as shown in the photos. Potential sand and respray so it matches the second bedside table.

I have a bed frame that’s slightly broken on one side — the wooden support has a dent but the overall structure is intact. Also,a wooden bench broken from The joints. Would you be able to repair or reinforce it? Based on the damage, I was expecting the repair cost to be around $50–70. Please let me know if you need more photos or if a small reinforcement piece would be required.

Need a new bolt as mine has come out and also to reattach the bed slats on one side

replace / fix bed frame , asap 2x(190x4x2cm)

Need to screw supports into side board. Must bring a drill. I have bought some 8g x 50mm screws. It’ll be super quick. Need it done ASAP

One side of my bed is broken needs to be fixed someone with tools ans screws to fix it

My bed frame broke and I need the wood frame replaced.

The base of my bed frame has come loose on one side, it is still connected however needs reinforcement with either a screw or some glue. On the other side it looks like both a screw and glue have been used.

When I had an overhead fan installed in the bedroom the light fixture was removed. The fan couldn’t be installed in the same place so the ceiling needs repair where the light used to be.

The end of my bed is collapsing and the wood is a bit broken

Bed Brogan. Needs repairing with steel angle fixing. - View all the details of this offer: https://www.airtasker.com/offers/01JKSAAHVG17B3G9VPTKR0FYZP

My bed keeps falling apart so need it fixed. The wooden planks (not in the photo) keep falling apart.

ETA: TASK ASSIGNED VIA PRIVATE OFFER Task is still showing as open, apologies. Not sure how to change that without cancelling. Hi there, Seeking offers for the following tasks: 1: Repair Double Bed Frame - The centre wooden beam of the base has broken in half, and the two legs attached to the centre beam have snapped off - The centre legs need to be replaced, and the centre beam either reinforced or replaced to restore the bed's stability - The beam measures 192.5cm long x 5cm wide x 2cm deep - The slats are not damaged, sit on top of the beam - ie not screwed or nailed to the centre beam 2: Hang 2 x Framed Pictures (please read carefully) - Each picture measures 72cm wide 82cm high x 6cm deep, and weighs 6kg - Wall is plasterboard on steel frame (no timber studs) - There is hanging wire attached to the back of each frame - One of the pictures needs to cover a fuse box on the wall - Due to the position of the fuse box, the top right corner of the picture will need to sit closely over the top right corner of the fuse box. See attached photo. This means it will need to be hung from hooks on either of the fuse box, rather than above - Please also consider that there will be wiring in the wall around the fuse box (most likely running vertically?) - The pictures are mounted at the front of the deep frame, so there's enough void behind to cover the fuse box and have the frame flush against the wall You will need to provide all materials & tools required to complete the tasks. Timing is flexible, but would be great if you're available either today or tomorrow after 1pm. Otherwise, later next week would work.