Find a reliable appliance technician in Toongabbie NSW

Need help with plumbing for washing machine at new house

Hi, I’m looking for a qualified technician experienced with Samsung refrigerators to diagnose and fix the root cause of the issue shown in the attached photo. I believe the unit is most likely a Samsung Family Hub French Door refrigerator (RF28/RF29 series), but I can confirm the exact model if needed. The issue began intermittently and, after repeated cancellations, the original error message is no longer appearing on the screen. However, the underlying issue persists: when the refrigerator doors are left open, the warning alarm no longer sounds after a few seconds as it normally should. At this stage, I am also unsure whether any other functions may have been affected and what this error code is referring to Please advise on your availability for inspection and repair. The quoted price is inclusive of labour and any parts or materials you may need to supply.

My electrical stove top and oven won't work, likely an power issue. the circuit for wall oven didn't trip stove top and oven are separate, both connected to the same circuit

I have installed a Bellini dishwasher (refer to attached image). From the outset, the unit has been displaying an “E5” error within 1–2 minutes of being switched on. Based on initial assessment, this does not appear to be a unit defect. The issue is most likely attributable to installation or supply-related factors, typically falling into the following categories: ~70% water supply / pressure / inlet configuration issue ~20% drainage installation issue ~10% potential appliance fault I am reasonably confident the appliance itself is not faulty, as the issue was present immediately upon installation. The installer also isolated and indicated at the time that the problem was likely related to the drainage setup and advised that it could be rectified on a subsequent visit; however, no follow-up visit has occurred to date. I am looking for someone experienced who can fix this Cost offer includes all labour and any parts that you may need to supply ( if any)

Fridge not cooling needs to have a look

Washing machine legs are loose and it moves slot. Needs to be tighted and aligned to stop shaking

Remove existing gas cooktop and oven and install new one.

Compressor doesn kick in - circuit board showing red led light blincking 4 times so definately isssue with compressor starting .

In between a drum clean, the washing machine abruptly stoped working and the water remained inside the drum. After sometime we could open the door and manually remove the water. We tried to turn it on the next day but then when we turn it on and try to start a wash or spin it sets the timer and then it gives multiple beeps and turns off. I assume the reason might be the overheating of the machine and the safety feature is turned on and we are not sure how to reset it.

Dishwasher water doesn't work properly, only fill in the bottom part. No water from the top and middle part.

Samsung washing front door sealer has to replace

My Samsung front door washing machine door sealer was damaged and has to replace new sealer

the dishwasher takes in water and immediately empties it out

Swap out my old slide out rangehood (60cm) to a new one (Bosch DFM064W54A). Range hood purchased.

Water drainage problem.There is light indication showing check water .

Water not draining light indication shows check water problem.

I need to replace BOSCH washing machine door seal gasket. I already have new gasket.

Hang Canvas photo, replace power switch boards, replace and install gas cooktop with rangehood

I have installed a solar batteries system, and it's working with the main house appliances and show the load, however I don't think it's connected to all the appliances such as air-con in the living room or granny flat sub board, because when those appliances are running, it doesn't show in the solar battery app. - my house is a 2 x 1-phase meter, 1 for any time use, 1 for controlled load with hot water - the sub board doesn't have meter, it only have switchers - my solar panel is 8.8kw and battery is 32kwh, it should be enough for all appliances - the meter board has been upgraded recently, no risk of asbestos Need: Electrician to inspect the CT clamp installation and ensure all circuits are being monitored correctly. Likely need additional CT clamps installed or existing ones repositioned to capture loads from all circuits including the air con and granny flat sub-board.

Hi, I need a licensed electrician to connect a new Devanti induction cooktop. The old cooktop has already been removed and the existing 240V single-phase supply cable (active/neutral/earth) is accessible in the bench cutout. The new cooktop has a standard terminal block with L1, L2, N, Earth and requires a single-phase install with L1/L2 bridged, as per the manufacturer’s diagram. Scope of work: • Hard-wire the new cooktop to the existing circuit • Bridge L1/L2 as per wiring diagram • Secure strain relief/clamp • Test operation + safety • Ensure compliance with AS/NZS 3000 Should be a straightforward job for someone experienced. Please confirm licence and availability. Thanks!