Find a reliable appliance technician in Dee Why

Tumble dryer no longer spins when hitting the go button. It’s trying to move as there is a whirring noise but just seems to be stuck. Even with a light load.

Disconnect and dispose of existing dishwasher and install new dishwasher.

When we replaced the oven in our rental apartment the shelf above it was a few mm to low. The installer took it out but did not have the tools to put it back on. The shelf above the oven is where the microwave oven goes. I just need the shelf put back on and the silver trim kit put back on that goes around the microwave.

Looking to move a dishwasher from Dee Why (1 flight stairs) to Milson's Point (4th floor with elevator) in North Sydney. Help with installation of dishwasher in North Sydney, replacing an existing washing machine. Options for transport only at a lower cost if unable to help with installation

I need a gas heater outlet moved around 1 metre to the left to be aligned under the power outlet (as seen in the photo)

A brand new Jumbuck BBQ was recently set up for a guest at our Stayz property, however, guests are saying that the gas bottle doesn't fit. We don't know what has happened to the manual and I'm unable to attend the property. I need someone to check it out, find a connection so that the gas bottle fits, or swap the bottle for one that does. Thanks

I need someone to remove and old slide out 60cm x 30cm range hood and replace it with a new one. Expectations is the old one will be taken away as well

We have a 6 year old SMEG espresso coffee machine and it is not pouring the shot. It sounds like there is something off with the pressure?

I need an electrician or similar to check my oven as it’s not working

Looking for a licensed plumber to help with a small laundry job. What I need done: • Remove and disconnect the existing laundry basin/cabinet and taps (see photo). • Install the new washing machine waste outlet setup as shown in the example image (the curved standpipe style). • Ensure everything is sealed, compliant, and draining correctly. • Cap or tidy up any unused plumbing points if required. Access & Details: • Laundry is small but easily accessible. • Washing machine is already in place. • Prefer someone experienced with laundry plumbing and standpipe installations. When: Flexible Please bring: All required tools and fittings. Let me know your quote and availability. Thanks!

I have a number of pool compliance issues that need to be fixed before 7 Dec 2025. Looking for handyman to help. If you are only able to fulfil a few of the jobs that’s ok too. Please let me know what you can fulfill and indicative $$. Council jobs detailed in photos attached.

One of the 4 gas burners does not stay on.

There is an error code flashing relating to the drain pipe of the washing machine

Remove existing gas heater and fit new one. Gas and water connections only

My Electrolux front-loader washing machine (model EWF12832) shows an E10 error — the water fills very slowly or stops during the cycle. I’ve already checked the hoses and filters, and the issue seems to be with the blue electrical connector on the water inlet valve, which looks cracked and may have a loose electrical contact. Sometimes the water starts when I move it, sometimes not. Looking for someone experienced with washing machine repairs to check the inlet valve / wiring connection and replace the part if needed.

Just moved in and need washing machine connected, lost a hose in the move it seems, front loader LG

Install a new Samsung washing machine and fridge. Connect the washing machine to water and put fridge into place without damaging walls.

I have a Bosch series 8 heat pump dryer and washer I just need someone to quickly stack them onto of each other with the stacker

I have the brackets for the dryer. I just need them attached to the wall

Dishwasher has stopped working. It’s making a gargling and whirring noise at the drain at the bottom with a small bit of water circling at the bottom of the drain (after taking the filters out) It also has two lights on the panel - the 70 degree is fully on and the rinse if flashing. It defaults to this when I try to switch it on.