Find professional window and door services in West Brisbane

Hi, looking at getting the height of my garage roller door stop adjusted up if possible. Is on a automatic opener. Located at Keperra

Sliding door cannot fully close, need wheel realignment

Fly screen doors need to be elevated by 20-25 mm as outdoor deck is going to be tiled.

The door doesn’t slide very well. When I open it, I need to lift the door up in order to slide it. The door has wooden frame and glass in the middle

Redo curtain rod fixtures Install sureflap into door (needs a jigsaw to cut hole) Install new tap onto sink & attach to water supply and gas

We have just had carpet installed and our doors are too long! Husband too lazy to this for me so asking nicely for help. Doors are already removed and there is a carport area where the cutting could be done (or take them away!). No idea what to charge - this is my best guess :)

Supply and Install Replacement Internal Bathroom Door Looking for a handyman to supply and replace a water-damaged internal bathroom door. Scope of work: Supply a new door panel measuring 2040 (H) × 810 (W) × 35 mm (T). - New door must match the existing door in style, panel design, woodgrain texture and colour. - Reuse the existing door handle, lock/latch and hinges. - Cut, fit, adjust and install the new door, including any required trimming, hinge recesses and handle cut-outs. Reference door: The following Hume door from Bunnings is the same design as the existing door, but is 10 mm wider (820 mm instead of 810 mm): Hume 2040 × 820 × 35 mm Internal Door Oak Oakfield HC2 https://www.bunnings.com.au/hume-2040-x-820-x-35mm-internal-door-oak-oakfield-hc2_p1972989 The replacement must fit the existing 810 mm width. Please allow for sourcing the correct size or arranging suitable trimming in accordance with the manufacturer's requirements. Please provide an all-inclusive quote covering the new door, materials, labour, and installation. Photos of the existing door and water damage are attached.

Can you quote for replacing the door frame as shown on the picture. Current frame is water damaged and need to be replaced .

**Quote & site visit only:** Licensed building contractor (qbcc licensed builder)needed – reinstall 7 aluminium sliding doors and associated linear board – Kenmore – immediate start Hi, We're looking for a licensed building contractor to reinstall 7 aluminium sliding doors and the associated linear board, 3 of which require lower flashing. The doors have already been removed, and waterproofing is currently underway (photo attached). We're after an immediate start. A site visit is required before quoting.

Supply and hang an external door. Must have a door lock. Amount excludes the door which can be reimbursed with receipt.

I need someone to come fix my kitchen cabinet door that’s come off the hinge

I need 3 x standard internal doors hung. Have all necessary hardware (doors,hinges, latches/locks and stoppers).

Need a normal indoor door closer for my internal office door at home. Happy for you to supply one or I can get it from bunnings if you can recommend one that you know works well and has a good soft close that can also be pinned open.

Cut to size and install the provided Delaco panels on the inside of carport / garage to partially enclose. Tasker to provide own tools, black head screws and wooden buttons to fix to. Panels are already purchased but will need to be cut to size. 6 packs of panels - total horizontal coverage 2.4m. Ceiling approx 2.5m high - panels are 2.9m

I x bedroom door repair and 2 x wall repair.

We have 5 or 6 interior doors that need to be removed and marginally shaved down to cater for new carpet. One door is already removed.

The cavity door to me bathroom has come off the rails. It is a new door and renovation.

The door latch is not catching correctly. It shouldnt be a big job however it is currently bothersome

Fix door handle. It fell off looks like the screw is loose. If not able to put back please supply and install a new one.

We’ve just moved house and one of the bedroom doors (nursery) is sticking at the top when closing and makes a loud noise. It needs to be shaved/planed slightly so it opens and closes smoothly and quietly. Looking for someone experienced with door adjustments/carpentry who has their own tools * Standard internal door * Sticking at the top (likely needs a small amount removed) * Want a clean, neat finish (no splintering or damage) * Ideally also check alignment/hinges if needed Location: Kenmore Timing: Flexible, but sooner is better (daytime preferred due to baby naps) Please bring your own tools and include your quote.