Find a professional garage door installer near you

Garage door needs greasing.

Hello. I’m looking for someone with experience in replacing a drive belt for a Liftaway garage door. I’m happy to pay for the replacement part.

I want to replace my old garage door opener & pulley track with a newer (3yrs old) one. Existing: Automatic Technologies GDO-7 V1 New: Automatic Technologies ATS-2V3 Tempo The new one should have all main parts and fixings, so mainly just labour and tools required.

Garage door makes noise when goin up and down i have applied WD40 but still naking noise

Looking for supply and install of automated roller or sectional garage door (dark grey in colour) for 2200mm height and 2500mm width (rough measurements). Existing sectional garage door needs to be taken off prior to new installation.

Garage roller door out of runner on the side, need help repairing

Weld cane drop bolt to bottom of garage door

I need assistance installing garage roller door. The frame is up but I cannot figure out how to install the door. 240cm height. 317cm wide Previous experience with garage roller door preferred

Need garage door service because sometimes door bounce back and stop

Hey Garage Door Experts, I was hoping to get your help with an issue we’re having with the garage door. One of the holders has come loose, and we’re struggling to open the door. The garage door service is also due. Hoping to get the task done today

I have a noisy garage door that needs fixing. I replaced the rollers a week ago but noise hasn’t reduced much.

I need both lift cables replaced and a full service on my double sectional (panel) garage door in Avondale Heights. One cable is visibly frayed (see photo). The springs are 9 inch, rear-mounted on the bar above the door, and appear OK, so no spring replacement needed unless you find a problem (please tell me first). The door has an automatic opener. The job includes: - Supply and fit 2 x lift cables - Full service: lube, check rollers, drums and bearings, check spring tension, balance and adjust the door, and safety-check the opener Please give an itemised quote (parts and labour), note any call-out fee, and the warranty you offer. Experienced garage door technicians only.

Need help with attaching a meross garage door opener to my ATA garage door, and also reprogram the garage remotes

This task is to diagnose and fix if simple solution is available. If more time and cost needed to repair once you have diagnosed, please quote. Our garage door fails to open. It may be that it is off the chain or something else is wrong. I can provide a video if nec. It tries to open, runs but does not lift the door for about 15 seconds and then sounds like it runs in the opposite direction for the same amount of time. The garage door never lifts. See photos for info about the make and model. It’s a pretty basic remote garage door system. Let me know if you have any questions.

Looking for a qualified and licensed carpenter to remove 2 single garage doors and replace with walls and windows - all garage door hardware to be removed by you and disposed of - 2 x single garage door spaces to be framed and windows installed. External cladding, frame and internal gyprock to be installed - need completed asap

Garage door spring is broken . B&d garage door brand 2017 build . Motor can lift or close the door because of spring . Budget is for quote .

Need to install a Meross garage opener, and neatly run the door sensor cable along the top rail and install the magnet, plug in the smart opener to the ceiling GPO, and stick the Meross onto the opener so the QR codes and button are accessible. No help required to configure wifi and app I’ve already done that. I have sticky cable clips if required. Garage ceiling is 3.7m high and the door opener is in the middle of the garage so you must have an A frame ladder that will be high enough to reach both the garage door and the power point on the ceiling.

Title: Urgent Help Needed – Broken Garage Roller Door, Car Stuck Inside (Berkeley NSW) Hi! We’re looking for someone who can help us remove our broken B&D Controll-A-Door 5 (CAD5) garage roller door. The door has stopped working properly, and we actually got trapped inside the garage. Our car is still inside, so we’re hoping to get this sorted as soon as possible. We’re planning to replace the garage door and just need the existing one safely removed before the new one is installed. I’ve attached photos to show its current condition. If you have experience with roller garage please let us know your best price and asap. Thanks so much!

TH ehigne og one of the part of the garade door was broken. Please see pic. Need to fix that and do geenral greasing and servicng making sur eit works properly.