Find an experienced builder in Georgia

Build the Hen House of Chicken Coop. Will provide materials & have the plan printed. Just need someone to spend the day putting it together.

Need a 10x10 shed assembled

Install 16×10 Aluminum louvered pergola with 3 sliding glass doors, led strip light, fan and heater

Deck Board Demolition: Remove and dispose of existing deteriorated deck boards that are damaged, rotted, or unsafe. Demolition includes carefully removing the existing boards from the deck structure while minimizing damage to the underlying framing and surrounding areas. All nails, screws, and loose debris will be removed, and the work area will be cleaned and prepared for installation of new decking materials. Any additional structural damage discovered after the deck boards are removed will be documented and submitted for approval before proceeding.

I have assembled most of the parts for a pergola but cannot stand it up and attach it together by myself

i bought a carport online. it’s metal and has installation instructions.

Build a Freestanding 84" Chicken Roost with 4 Bars and Poop Shelf I need a simple, strong, freestanding chicken roost built according to the attached drawing. The finished roost should be: 84 inches long 4 flat 2x4 roost bars, all at the same height Approximately 10 inches clear space between each roost bar Approximately 13.5 inches center-to-center between bars Top of roost bars approximately 36 inches from the ground. One chicken access ladder at one end. Strong enough for approximately 12–15 full-size laying hens Freestanding — not attached to a wall Poop shelf: Flat 3/4-inch plywood Approximately 84 inches long × 24 inches deep Shelf approximately 14 inches above the ground Runs underneath the roost bars No raised border or lip Center support underneath the shelf Construction: Primarily construction-grade 2x4 lumber Strong end frames Diagonal bracing as needed to prevent wobbling Exterior/construction screws or appropriate fasteners Sand any sharp or rough edges Structure must remain stable when chickens climb the ladder or move around on the roosts This is a straight rectangular design — no complicated corner construction. Please review the attached drawing before making an offer. When responding, please state whether your offer includes: Labor Lumber/plywood and hardware Building the complete unit Delivery to my location in Conyers, GA If materials are not included, please say so and give an estimated material cost.

Need an experienced, reliable person to prepare a simple paver base and assemble an 8' × 10' metal shed in Conyers. The 9' × 11' site will already be professionally graded and compacted before you arrive. No excavation or Bobcat work is included. Step 1: I already have the hardware cloth for predator protection. It simply needs to be rolled out flat over the prepared area, with the excess extending beyond the shed perimeter as an apron. Step 2: Lay approximately 99 concrete 12" × 12" patio pavers in a straight 9 × 11 grid. I will supply the pavers. They must be level, flat, stable and properly aligned so the shed has a solid, even foundation. No paver cutting should be necessary. Please advise if a small amount of leveling sand or minor base material is needed. Step 3: Completely assemble my 8' × 10' Breezz metal storage shed according to the manufacturer’s instructions, including the factory metal floor frame, doors, window, roof and all supplied components. Step 4 — CRITICAL: Properly anchor the shed to the ground so it is secure against wind. The anchoring must connect to the shed’s metal frame and use suitable ground/earth anchors or another appropriate method. Do not rely on the pavers alone to hold the shed down. Shed must be square and level, doors must open and close correctly, and the roof must be oriented exactly as shown in my photos/plans so water drains AWAY from the chicken run. I will supply the shed, pavers and hardware cloth. Please bring your own tools. Looking for someone with metal shed assembly and paver/leveling experience who can complete the work carefully and at a reasonable price.

Have a pergola with instructions, structure is put up just needing roof put up

Istall 111S Mirador Pergola with 13ft sliding doors, x4 panels, and 3 pull down screens

I have all the specific materials, I need help with placing the chicken wire on the coop and labor.

Extending Platform and Installing Shed

12 x 14 pergola purchased at Home Depot. Needs to be assembled and anchored to concrete patio

I recently purchased a new storage shed and need an experienced contractor or handyman to install it in my backyard. The site already has an existing concrete platform that was built for a smaller shed. The platform needs to be expanded and adjusted to match the dimensions of the new shed before installation. Scope of Work: Inspect the existing shed platform. Extend and reinforce the platform to fit the new shed. Ensure the platform is level, sturdy, and properly supported. Assemble and install the shed on the completed platform.

Need the section (pole to pole) of the fence removed and foundation demolished.

Would like to have this foundation demolished.

Shed 10*12 assembly, shed with the flooring. Concrete slab is ready but may need little leveling. Shed kit has already arrived.

Boxed pergola needs assembly per instructions then to be secured to concrete patio correctly. Must have proper tools for securing (hammer drill, etc). I will clear the area before the work and clean up after.

We have a shed outback that my wife wants to turn into a chicken coup. She has all the supplies but she needs help doing it

Concrete Slab and Shed Installation