Door Installation Jobs in Kent

Browse through over 500 Door Installation Jobs.

Why join Airtasker

Door Installation tasks in Kent

Check out what tasks people want done near you right now...

🔹 Job Overview: I need three sample table lamp bases made. If approved, I’d like to continue working with you in batches of 5-10 at a time. 🔹 Material Preference: Recycled wood/off-cuts preferred. Surface finish doesn’t matter, as I’ll be decorating them. Must be structurally sound and meet specific measurements. 🔹 What I Need: Hollow centre to allow for lamp wiring. Stable, balanced base for safety. Smooth edges for ease of decoration. a hole at the base for cord to exit and a hole at the top for an interior hollow rod. *Measurements in photos supplied in this post* 🔹 Future Work Potential: Ongoing collaboration if the samples are successful. Open to suggestions for efficiency in production. 🔹 Location: Based in Carlton, Melbourne, but happy to discuss pick-up/delivery options. 💡 If you’re experienced in woodworking and up for the job, send me a message with your rates and previous work samples! note: I have put a price of $30 in the post, this is just a filler with price per unit to be discussed.

Sun May 04 2025

about 2 hours ago

Open

I need to replace the old water pipes with new copper pipes for one storey, 4 bedrooms house. The highlighted red area are for bathrooms.

Sun May 04 2025

about 3 hours ago

Open

Balcony sliding door -install wheels - I have purchased them. -Install anti lift / slip to upper -replace rubber seal at threshold - (you’ll need to take it off to get a similar product from Bunnings) Floating shelf ; Install small L brackets to secure (have purchased the L brackets you just need the screws and plugs in black x 12 Fridge seal - replace - I have new one here . Will need correct glue . - change some wall plug sockets to have USB and USBC x6- need to purchase

Surfers Paradise QLD 4217, Australia

Sun May 04 2025

about 3 hours ago

Open

New set of Keihin FCR33mm fitted to a 1982 Kawasaki Z1300. I need someone to tune them properly. Currently tunning way too rich.

Sun May 04 2025

about 16 hours ago

Open

"Can you help me pair a Hills Activor remote control to a new fob? I have the original working fob and want to program the new extra fob. I can provide the instructions for reference."

Helensvale QLD 4212, Australia

Sun May 04 2025

about 17 hours ago

Open

I am based in Brisbane so please only respond if you’re located here too. I am after a small joinery unit to be made per the detail below. The lower section will house a small bar fridge so will need some venting on the back presumably. Details are in the image. For the top I will use one of the tiles I have 600 x 600 x 10mm so just need to be able to pop that in so its inset and level with the top of the unit. All visible surfaces finished in Polytec Perugian Walnut. Door soft close and push touch Drawer push touch. All measurements are internal measurements and don’t consider the thickness of the mdf. This should be made from 16mm mdf. I am ok to leave some of the internals as white melamine if that will make it cheaper.

Sun May 04 2025

about 18 hours ago

Open

I need someone professional who can replace my WH100xm5 headband hinge only (right side). It is broken atm. I have attached some photos below for reference.

Sun May 04 2025

about 19 hours ago

Open

We are closing in the carport area and are looking to give the front of the house a facelift. We want to match tour new windows (monument grey) with colourbond steal paneling. We like rich timber accents, a deep red door and facia (maybe). Leaving brickwork areas as is. Also need a window for the new closed in area on ground floor. The basic front of the house is to remain flat excluding the recess/return for the front door. Pic 1 is current facade while Pic 2 is incorporating some of our design ideas (not happy with it though). Note the supports on the ground floor limit placement of windows. Looking for a few different options

Sun May 04 2025

about 20 hours ago

Open

I can't seem to be able to print on the sheets I'm using in so confused I was told to use inkjet so did but it's just leaving a wet ink stain

Sun May 04 2025

about 20 hours ago

Open

Browse all tasks

Last updated on 5th May 2025

How to earn money on Airtasker

Job opportunities that find you

Set up notifications and be alerted when a nearby, well-matched job is posted. Let customers book you directly by setting up a listing. Provide a great service and work with them again with Contacts.

Set your price

Found a job you’re up for? Set your price and make an offer. You can adjust and discuss it later if you need to.

Work. Get paid. Quickly.

When tasks are complete, request for payment to be released and money will appear in your account instantly.

Post a task

We've got you covered

Whether you’re a posting a task or completing a task, you can do both with the peace of mind that Airtasker is there to support.

Airtasker’s insurance cover

Browse similar jobs in Kent

Blind Repairs

Curtain Rod Installation

Fitness Equipment Installation