Find a local electronics repairer in South London

Upstairs bathrooms -Removing the shower , toilet,the sink and the floor tiles on the two bathrooms upstairs -retailing the floor and reinstalling the shower, toilet and sink -painting the ceiling and walls in one bathroom -removing the old boxing around the pipes and building new one Kitchen -rehanging the kitchen cabinets -changing the sink and the tap -changing the drawer sliding sistem

Fitting of new kitchen laminate work tops, sink and cooker/hob. See pictures attached for dimensions.

I have bought some ready to assemble steps. Need someone to install so that it's securely fixed to wall and ground. Will also need to cover top concrete step with deck board so make it connected to the decking. May need to chisel out a few bricks to make it fit square.

Whole repaint of places shown, paint must be provided

Looking for an experienced labourer / groundworker to help dig service trenches at a house in Epsom. Work will mainly involve manual excavation for electrical / data service ducts, moving spoil, bedding/backfilling and general site labour. Routes and trench specification will be provided. 1–2 days’ work, likely late October / early November. Please quote your day rate and briefly describe any relevant trenching / groundwork experience.

Need someone to put splash back tiles on a small area of our kitchen. The tiles are stickers and come as two long strips they just need to be cut a little bit (with scissors) for the two plug sockets. Quite easy to do!

I need the following jobs done: ⁠1. Fitting a small amount of trim in our entranceway, attached to skirting board 2.⁠ ⁠⁠filling recesses either side of the bathroom door, possibly with caulk or wood 3. Fitting a threshold over the bathroom entrance 4.⁠ ⁠⁠ sanding a large cupboard doors slightly, so that it closes 5. Using a filler (acrylic?) to fill some small floorboard gaps

I need an Electronics engineer to repair the PCB board that is encased in the Monitor/Computer for my Racquet String machine from the 90's as the battery was leaking for several years and corroded the ICs / Trace lines so that the display no longer functions.Also a Molex female plug needs to be fitted which needs to be fitted to one end of a cable which connects the PCB board to the CRT power unit.I need someone who can spend time investigating the problem.Someone who can spend time looking at which ICs have been damaged and there are Trace lines that need replacing or re routing/bypassing certain components?Also a Cell Battery replacement is needed.The Electronic expert needs to spend time investigating thoroughly the problems.

Dismantle this elliptical cross trainer first then move this walking-pad from downstairs to upstairs in this location.

**1. Refit roller blind bracket** Roller blind bracket pulled out of the window reveal. Plasterboard anchors have torn out. Need old holes filled and both brackets refixed properly, either into the uPVC frame head or into solid material behind the plaster. One window, under an hour. **2. Reseal two kitchen sink areas** Failed sealant along the worktop to upstand joint at two separate sink areas in the same kitchen, plus around the base of the mixer tap at each. Rake out old sealant, clean and dry, reseal with mould resistant silicone colour matched to light quartz. Also tighten the taps underneath if there is any movement. Both Blanco undermount sinks.

There is leak from the ceiling downstairs that is directly below the shower cubicle upstairs. Need help to locate fault and fix

I have a gemmy animatronic butler. The circuit board is not working. I need it ch cl and repaired.

Replace 2 bath taps with mixer bath tap

My bathroom toilet keeps dripping into the toilet

Looking for someone to fill some gaps in my entryway flooring and a nearby skirting board corner. Two related jobs, same location: 1. Floorboard/parquet gaps — several gaps between wood blocks near the entrance, along the skirting board line. Need these filled with a flexible acrylic wood filler (not rigid filler) so they can move slightly without cracking out. Ideally colour-matched to the wood tone as closely as possible. 2. Skirting corner gap — a mitred corner joint has a small void behind it. Needs filling with flexible acrylic caulk, and the cavity behind it packed first if it looks hollow.

Waste pipe from bathroom shower has detached. Waste pipe from kitchen is leaking. Have new bath taps and plug that we want installed.

I need a new bed taken upstairs and assembled

I have all the supplies Feature wall and small kitchen counter

I need a new separate circuit on my switch board so I can plug in my slush machine : currently the circuit it’s on trips the rcd. So it needs its own circuit

One of the switches in the fuse box keeps tripping