Find a professional garage door installer near you

I received a meross smart garage door opener as a present and want to set it up. So any assistance with setting it up correctly would be greatly appreciated

Replace old garage roller door openers

Sectional garage door has become bent/bowed at the bottom and appears to be slightly out of alignment. Looking for someone experienced with garage doors to straighten and realign the existing door if possible. Prefer to repair rather than replace the panel. Photos attached.

Add same cladding to door surrounds as above garage door, if appropriate, or replace cladding above garage door & new around front door

- The track of the garage roller door (electric) is not aligned (the motor is fine). When you try to open the door it starts to bunch up on one side while the motor is running. In the meantime, we are pulling it down or rolling it up manually. - One kitchen sliding door is out of alignment, it’s stuck and is very hard to slide. - The last one is a kitchen cupboard door, with a faulty concealed hinged. The door is not closing properly. (we already tried adjusting the hinge, we suspect it’s broken)

One cable on my sectional garage door has snapped. I need an experienced technician to replace both cables and safely re-tension the springs. Tasker must supply both new heavy-duty cables and all tools. Must have experience working safely with high-tension garage door springs. Door is powered by an automatic opener.

Garage door is not working when remote is pressed, need a quote to repair and then once approved start the job.

Need to set up remote for garage door. For Eco residential 1000N.

Our garage door sensor has either been moved out of line or is faulty. Can’t seem to fix it. Also need to reprogram some new controllers and give it a general service. Experience required

I’ve recently had a panel lift/sectional garage door retrofitted to my garage in Carindale. Because the garage wasn’t originally set up for this type of door, there weren’t suitable fixing points in the ceiling where the installer needed to attach the overhead tracks/brackets. The garage door company is coming back to rectify the installation, but before they return I’d like suitable structural fixing points installed above the ceiling. There is good access to the roof/ceiling space via a manhole, with plenty of room to work. I’m looking for an experienced carpenter/framer who can assess the existing roof/ceiling framing and install appropriate timber blocking/noggins or other suitable structural framing at the required locations, so the garage door installer has solid fixing points for their brackets. I can provide photos and indicate where the garage door brackets/fixing points need to be located. Location: Carindale, QLD Timing: Ideally completed before the garage door company returns. Please bring the appropriate timber, fixings and tools. When responding, please let me know if you have experience with roof/ceiling framing or preparing fixing points for garage doors.

Old 1980s one-piece tilt garage door with strong extension springs/jamb fittings. I’m removing the door myself for renovations. I only need someone experienced with old tilt garage doors to safely de-tension and remove both counterbalance springs and confirm there is no remaining spring load. No full door removal or disposal required. Please only offer if you have specific garage-door spring / tilt-door experience. Early morning preference on Sunday 13/9/26

The garage door needs alignment and one bar need to be straighten

Need two garage doors removed, sitting out the front ready to go.

Must be done ASAP (Thursday 3 September) 5 minute job Garage door motor not working and technician is coming tomorrow to fix it. I just want to close the garage door overnight. It will need to be done manually using the emergency release and then lowering the door on the tracks. Not a difficult job, just something I'm not comfortable doing myself. Double garage tilt door. Springs are intact. As long as you try to close it manually, you will still get paid even if there is an unforeseen issue that stops the door from closing.

As per my description my garage door motor will not work

Need my Garage door and the side of the door (wall panted) has to be the beige/cream colour next to it Will provide paint Need to be proffesional done I will not be providing any equipment that is your expense. Thank you location double bay

TMT automation Garage door was pulled down manually while electricity was out. Later we tried to reset pulley and turn it on...motor unit keeps saying SF and wouldn't work.

Just discovered 4 spiders (3 red back and 1 unidentified black spider living behind a web) on our garage door and would love someone to come and kill them humanely by squishing them and then to clean up the webs. Hopefully today if possible.

Locksmith to replace broken deadbolt and rekey to existing key. Require similar to style shown with a long bolt.