Find a professional gate installation in Thornlands

I need someone to come to my property and repair a metal gate. The damaged part is the top hinge on one side of the gate. Each gate panel has two hinges, one at the top and one at the bottom. The top hinge appears to be broken or detached and needs to be welded/repaired. The bottom hinge may still be holding, but it may also need to be checked and reinforced if necessary. Job includes: * Inspect the damaged hinge and gate frame * Weld/repair the top hinge on site * Check the bottom hinge and reinforce it if required * Make sure the gate can open and close properly * Bring your own welding tools and basic materials Please quote your call-out fee and labour/material cost. Flexible with time, but sooner is preferred.

Hi, I’m located in Thornlands and would like an onsite quote for one side Colourbond fence plus two gates. Could someone please attend site to measure and provide a formal written quotation including supply and installation? Thanks.

Replace/ fix timber post and brackets to fix a timber gate

1. The motor itself is good; it runs normally and physically drives the gate. 2. When attempting to reprogram the travel limits (with DIP switch 1 set to ON), the gate cannot recognize the end points. In both the opening and closing directions, even after the gate has fully traveled and hit the physical end stoppers, the motor continues to drive hard and does not stop. 3. When observing the control board, the "REV" LED indicator stays solidly ON (constant illumination) while the motor is running, instead of flashing.

My side gate hinges have broken . Need to have them replaced 4 x external gate hinges put back on and gate operational again It’s two swinging gates that connect Hinges to be provided by installer

I need new remotes programmed with our Nice Hi-Speed gate (RUN1200 HS) ASAP I think I have the wrong remotes so would need those also

I need a simple gate built outside my house. The width is about 1600wide and height would be 1700 up to the existing fence line. I will need a simple latch as well. The timber finish is exterior grade pine.

aluminum gates for two pathways

Need to side access gate made and installed down the left side of our house. One side can be anchored to the timber fence and the other to the brick in the side of the house. The space is 90cm wide. Will need to have limited space underneath it so the dogs cannot get under it. Am open to ideas on style and materials.

Need someone to attach gates on my fence. Got the frame , just need to nail In the timber and attach it to the wall.

Hi. Wanting g a side gate supplied and installed. Timber or steel is fine happy to go with your recommendations. Width is around 920mm wide. Wanted gate 1800 high Thank you.

Hi there, I am looking for someone to affix a gate to brick house. Top hinge has come loose from wall & bottom hinge has actually snapped so needs replacing. Please see photos.

Excavator nudged driveway sliding gate, which bent in a few aluminum batten panels and popped a few rivets of where battens go into gate. Also bent the electric gate guiding post, which requires dyno bolting (x 4 bolts) back on concrete

Need detach the three screw ,the screw has rotten in the post, I want take the screw out of the post. - Due date: Needs to be done on 2023年12月6日 星期三

Got everything here, just looking for someone to install, Renner solar power gate. - Due date: Flexible

Looking for an experienced professional to repair the door stop behind this baby gate and repair the baby gate at the top of the stairs. Would also like a curtain rod installed in our laundry. Need this job completed this week, as the hallway is being painted next week. - Due date: Before Saturday, 8 April 2023

Wanting a gate built to block off the back section of the house. Same simple timber finish as the fence The space is 1.7m wide - Due date: Before Saturday, 16 July 2022

Need quick fence thrown up, dog is getting out. Have 3 sheets of colourbond, one post. The existing gate is very heavy, but I would like to reuse or make new one? Length 3.7m Need done asap.