Find a professional gate installation in South West Perth

Need a handy man to repair a broken metal side gate latch. The metal locking rod has come loose, with a broken fixing bolt. Fix the existing parts where possible, or replace the damaged components if necessary. Photos attached.

I have a 2.5m gate / fence that I need to move forward about 3m. I don’t know for certain if the fence is working as a retaining wall at all, it doesn’t look like it is but it’s butting up against the side of a raised garden bed (the front of the garden bed is a brick retaining wall and the side also appears to have bricks). See photos for reference, I want to move the fence to be past the bins. I may also need a small extra bit of fence against the side of the house as ideally I want to move it 400mm past the wall in the fourth photo

Reprogram electric gate.

The very top button on this DEA GT14 remote is faulty. All the other buttons work fine, but only the top one is programmed. Id like someone to unsolder and swap 2 of the actual buttons. I tried to soldier but suspect mine wasn't hot enough to get this job done.

Need to change the direction the gate opens to the outside of the house rather than the inside of the house.

Repair and reattach an existing timber gate. Bicton WA 6157, Australia I’m looking for someone to repair and reattach an existing timber gate. The gate and gate posts are already in place, but the existing hinges and latch need replacing. The job would involve: - Supply and install 2 suitable new heavy-duty gate hinges. - Reattach the existing gate securely to the existing gate posts. - Supply and install a new latch similar to the one shown in the attached photo — preferably a sturdy black powder-coated latch. - The existing gate may need 2 new timber slats/rails fitted to provide a solid fixing point for the new hinges. - Check that the gate is properly aligned, opens/closes smoothly and is securely supported. - Minor adjustment/repair to the existing timber as required. Gate and posts are already there — this is primarily a hinge, latch and reattachment job rather than a new gate installation. Please include labour and materials in your quote, and let me know if you need any further photos or information before quoting. Images sent previously

Re-attach gate post to wall and align gate.

Gate is fixed to house with brackets, one of which is quite close to conduit. Side panel has spigots concreted into a narrow flower bed close to a retic pipe. Ideally the concrete will be dug out and removed with the spigots. If this isn't possible without damaging the retic the spigots can be cut below ground level so the upper parts of them can be removed as long as the parts remaining in the ground are made safe (ie, not sharp). Access is via a side gate (app 1 m wide) on the other side of the house or via a narrow walkway and through the rear garage door.

I need repairs to my steel gates. Main gate is dented. Rust spot on the hinge to the pedestrian gate needs repairing.

Install a new colourbond side gate and concrete the post in.

Require pool gate hinge installed on post.

Supply and install Colorbond side gate and panels – Orelia Looking for someone to supply and install a Colorbond gate and fixed panels at my new build in Orelia. The boundary fencing has recently been installed, and I’d like the colour and profile to match. Work required: - Larger side – approximately 2 m wide: Install a pedestrian gate and fixed panel across the opening. - Smaller side – approximately 900 mm wide: Install a fixed panel to close off access. No gate required. Measurements are approximate and will need to be confirmed on site before fabrication. Please quote for the complete job, including materials, posts, gate hardware and installation. Photos of both areas are attached. Please include your availability and estimated lead time.

I’m looking for someone to repair and reattach an existing timber gate. The gate and gate posts are already in place, but the existing hinges and latch need replacing. The job would involve: - Supply and install 2 suitable new heavy-duty gate hinges. - Reattach the existing gate securely to the existing gate posts. - Supply and install a new latch similar to the one shown in the attached photo — preferably a sturdy black powder-coated latch. - The existing gate may need 2 new timber slats/rails fitted to provide a solid fixing point for the new hinges. - Check that the gate is properly aligned, opens/closes smoothly and is securely supported. - Minor adjustment/repair to the existing timber as required. Gate and posts are already there — this is primarily a hinge, latch and reattachment job rather than a new gate installation. Please include labour and materials in your quote, and let me know if you need any further photos or information before quoting.

Remove old panel of fence 2.5m wide, 2 x metal poles -remove with angle grinder. 5.3 metre wide space at back of garage, to include 1 x aluminium pool gate 1.8m high, self closing gate with key lock to both sides. Put in 4 stand up poles to attach gate and frame. Construct frame top and lower levels to attach ekodeck batten screen panel 219x26mmx3.6m, onto frame. And a section onto the gate to match. Then repeat this process for a gate 1.5m wide, to cover path, this is at back side corner of home, 4 stand up poles, make frame and attach ekodeck to frame. ASAP

The pool gate needs to shut automatically. At the moment it remains open.

One hinge on a metal gate needs fixing back into brick wall. Needs someone with ability to drill into brick to attach gate hinge.

Hi, I’m in Coolbellup and looking for approximately 20 m² of exposed aggregate concrete. Side of house and backyard. Could you please give me your best supplied-and-laid price, including preparation, mesh, concrete, exposed finish, sealing. Thank you

Need a gate installed at side of house, whole gap is 1940mm between pre-existing fence and house, will need to be 1800mm high and will need to be solid (no see through parts) and in colourbond colour woodland grey or monument.

The metal frame of a colour bond gate needs repair. Likely need to be welded. Gate does not close/latch properly. In the winds last night the gate has come open a ripped off the already loose latch on the bottom of the gate. As the top latch also does not reach at all and need to be fixed. The quote here is notional and extra costs can be added later.

I'd like a gate installed in my fence.