Find a professional garage door installer near you

Garage door needs a service. Not sure on what the costing would be

We need an experienced garage door installer to complete a job for our customer. Install + Supply Requirements: - Proven experience installing garage doors - Relevant licence and public liability insurance - Own tools - Professional and tidy on site, since you'll be attending on behalf of our company The customer's address and contact details will be shared once the task is assigned. In your offer, briefly mention your experience and how long you've been installing garage doors. Ceiling height: 2330 mm Opening height: 2150 mm Opening width: 4800 mm Garage width: 5270 mm

Purchased from China and it cladding garage door

The garage door is opening half only and the pulley is working but the door is not fully closing. The door closes till the bottom and open automatically

Merlin Garage door does not open.

I need someone who is experienced at replacing springs on an electric garage door to replace our garage door springs.

Someone has hit our garage from outside and the door is now bent

frayed and snapped cable on one side of the garage door (panel lift) needs replacement

I've already bought all the parts from Bunnings and need labour only: removing the old opener and properly installing the new one. Parts supplied by me: Chamberlain SectionalLift Plus (CS105MYQ), with its own new rail and drive Chamberlain myQ Connectivity Kit (myQ Gateway + Safety IR Beams) The job: Remove the old opener completely, including the old chain and rail, and take them away Install the new opener with its new rail on my [single / double] sectional door Mount the Safety IR Beams on both sides of the door and wire them neatly to the opener (cables clipped, no loose wiring) Connect the myQ Gateway to my router and pair it with the opener Set up the myQ app on my phone and test open, close and alerts Program all remotes, including the car visor remote Set travel limits and force, and test the safety reversal and IR beams Check that the door is balanced and running smoothly, and let me know if the springs or rollers need attention Show me how to use the manual release Details: Location: Oakleigh East Door: single sectional, single garage townhouse Power point in the garage ceiling: yes

Looking for quotes for someone to fix my Merlin garage door remote. The garage door works fine using the button on the motor, but the remote has stopped working. I’ve already replaced the remote battery and it still doesn’t work. It’s a Merlin SilentDrive Elite

This morning tried to open garage door and didn’t open and saw the springs on floor Need a professional/ expert to secure the springs and get it relyable working Springs only came off on one side - other side still connected

Looking for an experienced painter to prep and spray paint two existing timber garage doors in Colorbond Monument. Two coats required with appropriate preparation and masking/protection of surrounding driveway, walls and garden. Please advise whether your offer includes paint and materials.

Just need a servicing on garage door

Looking for a handyman or garage door technician to inspect and service my automatic garage door. The door functions fine (opens and closes normally), but it makes a persistent noise during operation.  I have already applied garage door spray lubricant, but it hasn't resolved the issue.

- The track of the garage roller door (electric) is not aligned (the motor is fine). When you try to open the door it starts to bunch up on one side while the motor is running. In the meantime, we are pulling it down or rolling it up manually. - One kitchen sliding door is out of alignment, it’s stuck and is very hard to slide. - The last one is a kitchen cupboard door, with a faulty concealed hinged. The door is not closing properly. (we already tried adjusting the hinge, we suspect it’s broken)

Garage door will not close. Gets 1/3 of the way down, beeps then opens up again. It cannot be locked. We manually close it, place a pot plant to hold the door in the down position. Looking for someone to repair it.

Need to set up remote for garage door. For Eco residential 1000N.

Our garage door sensor has either been moved out of line or is faulty. Can’t seem to fix it. Also need to reprogram some new controllers and give it a general service. Experience required

I’ve recently had a panel lift/sectional garage door retrofitted to my garage in Carindale. Because the garage wasn’t originally set up for this type of door, there weren’t suitable fixing points in the ceiling where the installer needed to attach the overhead tracks/brackets. The garage door company is coming back to rectify the installation, but before they return I’d like suitable structural fixing points installed above the ceiling. There is good access to the roof/ceiling space via a manhole, with plenty of room to work. I’m looking for an experienced carpenter/framer who can assess the existing roof/ceiling framing and install appropriate timber blocking/noggins or other suitable structural framing at the required locations, so the garage door installer has solid fixing points for their brackets. I can provide photos and indicate where the garage door brackets/fixing points need to be located. Location: Carindale, QLD Timing: Ideally completed before the garage door company returns. Please bring the appropriate timber, fixings and tools. When responding, please let me know if you have experience with roof/ceiling framing or preparing fixing points for garage doors.

Old 1980s one-piece tilt garage door with strong extension springs/jamb fittings. I’m removing the door myself for renovations. I only need someone experienced with old tilt garage doors to safely de-tension and remove both counterbalance springs and confirm there is no remaining spring load. No full door removal or disposal required. Please only offer if you have specific garage-door spring / tilt-door experience. Early morning preference on Sunday 13/9/26