Find local downlights installers in NSW

Install 4 downlights. Currently has a fan with light . Small room of 2.5 *3 m

Hi, I need a licensed electrician for a few jobs at my place in Kingsford (old single-storey brick house). I've already got the main parts, so it should be mainly labour. 1. Living room lights: swap the 6 old halogen downlights for new LED ones (SAL Wave, plug-in type, 72mm cut-out). Remove the old transformers and lamp holders, fit a plug base on a joist next to each light (not buried in insulation), and set the lights to warm white (3000K). The existing holes are about 70mm – please don't enlarge them unless necessary. Test one on the dimmer before fitting the rest, and take a photo of where the plug bases are. 2. Living room switch: replace it with a Clipsal Iconic switch + rotary dimmer (switch on the left, dimmer on the right). Brick wall and the dimmer is about 55mm deep, so it may need chasing deeper. No flicker or buzz when dimmed, and please set the minimum level. 3. Data cable: run one Cat6A cable (about 15m) from the bedroom to the living room through the ceiling, using the existing holes. Cable and keystones are shielded – please bond the foil and drain wire to the keystone at both ends. Registered cabler needed. 4. Safety check: switchboard and roof wiring, especially an old junction point on a timber block. Fix anything unsafe (ask me first if it costs extra). Remove old dead wiring and fittings that definitely aren't needed. Please leave the alarm panel alone. 5. Wiring: let me know if the house wiring is old or worn. 6. Quote only for now – do I need these, and how much? - New switchboard - Upgrade from 80A to 100A - Three-phase – is it available in my street, and roughly what would it cost? - Surge protector I'm also planning ducted AC, a heat pump, solar + battery and maybe an EV charger – does that change anything now? Good to know: - Ceiling and insulation tested – no asbestos. - Ceiling is fragile – please only step on joists. Please include your licence no., ABN and insurance. CCEW needed on completion. Feel free to quote. Thanks!

I need an electrician to replace the heater lamp and fan unit and it needs to cut the ceiling to fit the new one and also replacing 4 downlight in the kitchen and living room

Downlights supply and install

Lights and plug points already purchased. Instalation only. 5 double GPO, 1 muti-gpo(office), 4 down lights in pergola (provision provided), Install 1 outdoor sensor light to the pergola post or eve wall

Have 1 recessed downlight in apartment that needs replacing. Not sure of bulb type tasker will need a ladder

Need to replace existing lights with downlighting

Replace 11 globes for down lights,

Hi there, I need someone to change the color setting on the ceiling downlights throughout the house from cool white to warm white. These are built-in Tri-Colour LED downlights, so they do not need new bulbs. You just need to pull each fixture down slightly and flip the manual toggle switch on the back over to the "Warm" setting. Important Details: • High Ceilings: The house has high ceilings, so you will absolutely need a tall A-frame ladder or extension ladder to reach them safely. Please bring your own tall ladder/equipment. Looking for someone who can get this done quickly and safely. Thank you!

I need help to repair or replace a bathroom downlight/exhaust fan combo. The light is not working but the fan is still working as normal

We have a bathroom light that won’t turn on properly (dimmable down lights with a push/twist switch). They will only come on super low and can’t be turned up. The fan and heat light on the same switch work, and there seems to be a slight buzzing from the switch board at time.

I have a single downlight in the dining room that pops on/off and sometimes not at all. I've changed globes - that's not the issue. I also have an exhaust fan in an ensuite that does not work.

Hello, We are looking for a licensed NSW Electrician to replace two faulty ceiling downlights in our optometry room in Erina Fair. The Issue: Two recessed LED downlights in our main optometry room have gone out. Adequate lighting is essential in this room for our clinical processes. As these are integrated LED units (not simple screw-in globes), the entire fitting/driver needs to be replaced. The ceiling height:—approximately 4 meters. The Job: The task is to supply and install new replacements for both faulty downlights. The scope of work includes: 1. Safely accessing the high ceiling (a suitable tall ladder or platform is required). 2. Removing the two faulty downlight fittings and their drivers. 3. Supplying and installing two new, matching white recessed LED downlight fittings and drivers (standard warm white, dimmable). 4. Testing both lights and the dimmer switch (if applicable) to ensure they are fully operational. Please note: The successful contractor MUST supply the two new compatible replacement downlight fittings and drivers. The cost for this hardware must be included in your final offer. Requirements: - MUST be a fully licensed and insured NSW Electrician. - You must have your own tools, including a tall A-frame ladder or platform appropriate for a 4-meter ceiling height. - Experience with commercial LED lighting installations. Location & Timing: Location: Terrigal Dr, Erina NSW 2250 When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a comprehensive quote for the complete supply and install. Thank you.

Hello, We are looking for a licensed NSW Electrician to replace two (2) blown ceiling downlights at our retail store, in Newtown. The Job (Labour Only - Lights Supplied): 1. The replacement fittings are already purchased and provided in-store (2x DETA 160mm LED downlights with plug-in drivers). 2. Safely access the ceiling on the sales floor (appropriate A-frame ladder required for a commercial ceiling). 3. Remove the two faulty downlights and drivers. 4. Install the two new downlights (ensure the tri-colour switch is set to 3000K Warm White to match existing store lighting). 5. Test both fittings to ensure they operate correctly. Requirements: -- MUST be a fully licensed and insured NSW Electrician. -- You must supply your own tools and a suitable ladder for commercial ceiling height. -- Public liability insurance is required. Location & Timing: Location: King Street, Newtown, NSW 2042 When: The job can be completed at your earliest convenience. Please state your availability in your offer. Please provide a quote for the installation labour. Thank you.

Rebooking task between James and Manogran

For a licensed professional electrician to install four downlights in the new ceiling of our kitchen and also install an electric oven and install a double PowerPoint from the current rough in work down by another electrician

Install 2x1.2m long LED strips under bathroom cabinets(Power is available inside the cabinet) Replace 13 existing socket style downlights with plugged in DL's Replace existing GPO to recessed. All supply and Install.

Looking for a licensed electrician to remove 6 existing MR16 halogen downlights and transformers and replace them with modern integrated LED downlights. I already have 4 of the LED downlights but I think I need a transformer - refer to images of existing halogen and current stock of 4 downlights. In your offer advise on price reduction amount if you can use the existing ones I have. Please supply and install 6 x good-quality warm white (3000K) LED downlights, ideally tri-colour selectable and IC-4 rated. Existing ceiling cut-outs to be reused where possible. Price to include LED fittings, removal/bypass of existing transformers, any required plug bases/connectors, installation, testing and disposal of old fittings. Please confirm electrical licence and brand/model of LED being supplied. Budget: $350 all inclusive. Apologies all I wrote 5 instead of 6 for the supply and install - please make necessary adjustment for those who quoted for 5.

Downlights supply and install for top floor of second story house , about 15-18 lights and install pendant light downstairs in the kitchen where power is all ready.

ceiling downlight/light fitting is not working and appears to need replacement. Living room x2 Bathroom x1 Looking for a licensed electrician to inspect and replace the bulb/fitting as required