Find a professional staining service in QLD

I’m looking for an experienced painter or carpenter to restore the timber slats on the front of my home (see attached photos). The job involves: * Inspecting the existing timber for any damage. * Light sanding/preparation of the timber slats. * Cleaning the surface. * Applying a suitable exterior timber stain or clear protective coating (ideally matching the existing finish). * Ensuring an even, professional finish. The timber slats are located near the roofline above the front entry, so the successful Airtasker will need appropriate ladders or access equipment. Please include: * Your experience with exterior timber restoration. * Photos of similar work you’ve completed. * Whether your quote includes all materials. * The type of stain/coating you recommend. I’m looking for a quality, long-lasting finish rather than the cheapest option.

Hello, I need some stainless steel bolts cut down so they are not protruding. In a boat cabin. Prefer then to also be smoothed down so not a hazard for people. Thanks

I need about 5.9 lineal metres of s/s wire balustrade installed/fitted. I can supply all the materials. To be fixed into steel RHS posts. 1 @ 3.5 wide and 1 @ 2.4m width. x 900 high. Would need to have experience with this system preferably.

Deck is 6.75m wide and 5.15m long I have leftover boards if any need replacing, and I believe I have deck cleaner and stain that I can provide.

Require a stainless steel spot weld repair of two 316 outlets in a stainless tub.

Require stairs to be stained in a different colour.including borders and balastrades.

16 treads including rises to recondition and recoat

Build complete timber decking for front porch section of new house build. Lookign to have deck surface treatement to similar colour as existing door.

The decking around my pool is in need of sanding and staining

Weather worn area of deck and stairs. Needs restaining - I have the stain required

There is a splat of Prosecco on the roof. It is a small area but I need to fixed before moving out this rental. Perhaps 0.5x0.5m affected in total. Unfortunately I don't know the exact colour of white on the roof used to paint over

A commercial stainless steel table and an aluminium 300mm high needs to be cut to create a 900 mm opening to access the backside of the shop

Looking for an experienced carpenter, deck builder or balustrade installer to install a 316 stainless steel wire balustrade system on my front deck in Eagleby, QLD. Materials supplied by me (Chaindirect - Balustrade Basic Kit (No.6) – Turnbuckles (33), Wire (150m), Fittings, Tools Kit): 316 stainless steel wire balustrade DIY kit 3.2 mm 1×19 marine grade 316 stainless wire Turnbuckles, end terminals, saddles and all fittings Hydraulic swaging tool and cable cutters Work required: Remove and dispose of the existing timber balustrade infill only (existing timber posts and top rails to remain). Install stainless steel wire terminals and cables. Tension all wires evenly. Ensure the installation is straight, secure and professionally finished. Clean up and remove all waste upon completion. Project details: Approximately 7 railing sections 8 horizontal wires per section (56 wire runs total) Total railing length approximately 12 metres Existing timber posts and handrails remain Stainless steel wire system only (no glass) Requirements: Experience installing stainless steel wire balustrades. Own tools (other than the supplied swaging tool and cable cutters). Please provide photos of previous similar work. Installation must comply with Australian residential balustrade requirements. Please include with your quote: Your experience with similar installations. Estimated time to complete. Total labour cost. Any questions after reviewing the attached photos. Location: Eagleby QLD 4207. Must visit in person to confirm the full job and understand work. Budget: Looking for quotes.

Pressure clean concrete and stain timber deck - Eagleby Looking for an experienced person to: Pressure wash timber deck. Light prep/sand where required. Apply 2 coats of quality decking stain/oil. Pressure clean surrounding concrete paths and patio Please include labour in your offer. Happy to either supply the stain or have you supply it if you recommend a quality product.

Prep and clean new timber fence and apply solid timber stain to boundary timber fence (approx. 83m). Can supply material but not tools.

37.8m2 deck to be lightly sanded and restained.

We have roughly 140sqm of deck that needs to be prepped, sanded and stained in Samford Valley. 25sqm of the deck needs to be sanded back to bare the rest is a light sand.

Need the back deck sanded and stained

Will pay hourly rate. I am preparing my home for the rental market, so I need lots of small jobs completing. Most of my fly screens need new mesh, stainless steel bath drains need replacing, leaking tap, a few gaps filled and general maintenance. Thank you!

Sand, fill & oil timber deck (36m²) Looking for an experienced deck sander/finisher to sand back, fill gaps/cracks where needed, and apply 2–3 coats of a high-quality oil/stain to merbau colour (e.g. Intergrain, Feast Watson, Sikkens or equivalent). Deck is ~36m², wide hardwood boards (solid Aussie timber). Please include: • Equipment (proper floor/deck sander, not handheld only) • Product you recommend/use