Find experienced local carpenters in Outer West Sydney

Need to remove existing drawers/ cut carcass to provide place for dishwasher. Remove existing oven in kitchen. Measure, supply and install 3 drawers (soft close & fingerpull )in oven’s place

Looking for someone to build a custom storage box for our motorsport parts showroom. We currently have wooden storage boxes with compartments for storing sprintcar radius rods upright, and we’re wanting a new one made. Approximate dimensions: * Length: 1220mm * Width: 260mm * Height: 320mm We would like internal dividers to separate the different sizes of radius rods, with enough room to store multiple rods in each compartment. Ideally, we’d like it made from plywood or MDF with a neat, professional finish suitable for our showroom. Photos of our existing storage boxes and a rough measurement sketch are attached for reference. Looking for someone who can supply materials and build the complete unit. Please send through your quote and availability. Also need delivery to Bligh Park. Thanks

I would like to cut a recess into the laundry wall to put my cabinet in

Cabinet maker, drawers, benchtop and splash back

Remove old wall shelves, assemble and install wall cabinet. Install 2 roller blinds. Remove old plug in rangehood, install new plug in rangehood.

3 appliances to be welded with brackets to stainless steel in food trailer

Looking for an experienced Kaboodle installer/cabinet maker to complete the finishing work on our laundry cabinetry. Cabinetry is already installed and all required Kaboodle parts/materials are supplied. Work required includes fitting/cutting the kickboard and end panel, adjusting and aligning the existing cabinet doors/fronts so gaps are even, and assembling/installing a Kaboodle laundry cupboard insert inside an existing tall cabinet. Important: the laundry cupboard insert is slightly too deep for the existing cabinet, so it will need to be accurately trimmed/reduced in depth before being assembled and installed. Please bring all tools required for accurate, clean cabinetry cuts and installation. Looking for someone with cabinetry/Kaboodle installation experience rather than general furniture assembly. Photos attached showing existing cabinetry and tall cupboard.

Looking for a builder/handyman to cut and fix Merbau Decking to steel posts going up a set of stairs. I already have the timber and fixing screws.

I’m looking for a carpenter or handyman to help me with my bed base. The bed base is too large to fit through the stairs, so I need someone who can disassemble it, move it upstairs, and reassemble it in the bedroom.

I need to get a quote for a cabinet and installation, similar to the photo attached Height 233 cm Width 333 cm

Needs cabinets similar to the below picture installed in one of my room sliding door closet. I need one each on either side.

Balustrade installation needed

1x Straight Track Saw Cut. Handyman with a track saw/guide rail for a quick, 10-minute job in Kingswood. In an out.. ​Task: Make 1x clean, straight cut on a Kaboodle timber benchtop slab to fit a wall-to-wall microwave nook gap (~1,536mm). ​Details: - ​Benchtop is already sitting elevated on sawhorses and ready to cut immediately. - ​Zero joining or complex edge routing needed—just one precise, straight cut. ​Requirement: Must bring a track saw with a guide rail and fine-tooth blade to ensure a clean, chip-free finish.

Fix 70x35 battens with packers Cut few timbers and adjust Approx 2 hrs job

Kitchen draw has collapsed and guide rail has come off cabinet wall

Build a doggy door to fit a sliding door.. two posta approx 2000mm with a ply insert width approx 250mm leaving a gap at the bottom of approx. 300mm.attach using existing screw holes in frame.move lock latch plate to side of door. It's a rental so needs to be removable without damage to frame.i bought a premade, but the frames not quite true so it doesn't fit. I can attach a flap later and paint it later.

Looking for a handyman to repair a damaged timber window sill/frame. The bottom section and right-hand corner have deteriorated and need to be repaired or replaced as required. The aluminium window itself appears fine the job is mainly the surrounding timber. Looking for someone who can: * Remove damaged/rotted timber * Replace/repair the affected sections * Seal and prepare the area properly * Supply materials if possible Photos attached showing the damage. Located in cranebrook, NSW. Please let me know your quote and whether materials are included.

After someone who can make me something similar to this Ideally 1.8m - 2m in length

Hi, Looking for someone to replace my kitchen cabinet doors and drawers. Just looking for a cheap and simple job, nothing fancy. Happy with basic materials to keep the cost down. Please send me your approximate price.

Assembly 3 shelf units - images available with dimensions