Find professional window and door services in Sutherland Shire

We have broken door hinges and have not been able to find the same hinges to replace. We need someone who can replace the hinges so the door can close properly.

Looking for an experienced garage door technician to supply and replace the torsion springs on my double-car sectional garage door. One of the existing dual-torsion springs has snapped (I require BOTH springs to be replaced as a matching set so they are balanced and fresh). Door Type: Double-width sectional panel door Opener Model: B&D Controll-A-Door Advance V2 (Model: SDO-2V2 ADV) - motor is healthy and safety-reversed correctly. The Job Requires: 1. Supply of 2x matching high-quality replacement torsion springs. 2. Complete installation, tension winding, and physical balancing of the door. 3. Re-engaging the B&D motor and resetting/testing the travel limit cycles. 4. Brief safety check of the lifting cables. Please include the cost of the parts (both springs) and labor/GST in your offer. Hoping to get this sorted as soon as possible. Thanks!

Hang 3 internal doors They were already hung but changed the flooring now need to cut doors down and hang them again

Patch up a crack about 10cm in front door.

Description: I am looking for an experienced carpenter or handyman to fit and hang 4 internal doors following the installation of new carpet and floorboards. Scope of work: Measure, trim and fit 4 internal doors (1 is a sliding door) to suit existing door frames and new floor heights. Install door handles/latches and any required hardware. Not included: Painting or finishing of doors. Supply of doors. Additional assistance requested: Advice on suitable door types, sizes and materials to purchase before installation. Recommendations on any hardware required. Please include in your offer: Relevant experience fitting internal doors. Confirmation of any materials you would expect me to supply. Estimated time required to complete the job. Timing: Ideally to be completed around 25 July 2026, once flooring installation has been finished.

I need an experienced handyman, painter, or maintenance tradie to complete two exterior repair tasks at my property: repairing a crumbling concrete/render section beneath a front door threshold, and prepping/painting a weathered timber window sill.

Looking to have an outdoor pull up installed in my yard. It needs to be cemented 50cm into the ground & assembled.

Front door needs planing approx. 10mm. No need to take the door off.

Need this front door to be operating properly and not slamming loudly. Current state: - Getting stuck wide open (mechanical arm is jamming). - Door has been bent overtime vertically, which isn't helping. - Slamming shut very loudly (no combination of the hydraulic tuning has succeeded so far. Open to using a different arm - Door latch is operated

Need to raise the door by a cm

Need to replace this rail on the door with the new rail. I already have purchased the new rail.

Replace 2 door handles inside the house. Replace hang one tv with brackets already attached to the wall

I need a door replaced, the new door is onsite, use the existing lock and hinges, you don’t need to paint the door, just apply primer paint which you will need to supply to the top, bottom and sides of the door. In your price include rubbish removal of the old door. Need 10 ceiling tiles replaced, the new ceiling tiles are onsite. In your quote include rubbish removal of the old ceiling tiles.

Looking for someone to wire a small smart home device (ratgdo32) to my Merlin MS65MYQ garage door opener in Miranda. The device is already purchased and the firmware is already installed — I just need someone to physically wire it up and mount it to the opener. The opener is ceiling mounted so you will need to bring a ladder. What's involved: • Connect 3 wires (red, white, black) from the ratgdo32 to the opener's terminal block • Mount the ratgdo32 to the opener rail using the included clip holster • Plug the ratgdo32 into USB power (powerpoint is right next to the opener) The job is straightforward — only 3 wires, no pass-through connectors, no wall button wiring. Full written instructions and photos of the actual terminal block will be provided. The orange pass-through connectors on the ratgdo32 are not used. Note: this is an Australian model opener so the wiring differs slightly from the standard US diagram. Instructions make this clear. Full wiring reference: https://ratcloud.llc/pages/wiring

Need a plasterer to gyprock a bulkhead above a balcony window. Size: approx 3190mm long x 405mm high Install gyprock and set (tape, base & top coat) Finish ready for paint (no painting required) Indoor access, straightforward job I also included a photo of the underside of the wood panel as there will need to be a return to cover the underside. Photos show blinds but will remove

Mash replacement of upper area of a screen door and separate window. The frames are old and I need someone who is skilled in that area. Since I am renting I dont need frame work done.

I have 5 doors that need to be installed. Old doors taken away also. I have the new doors already just need installation.

New fly screen installed in sliding door (polyester/polypropylene). Replace rollers on glass sliding door (pic 3: door has started jamming).

Need this doorway rendered, with angles installed on all edges. Needs to be finished perfect ready for paint 👌

Our ensuite pocket door is no longer opening and closing with ease, it’s really stuck. We have tried to adjust it but think it may have have come off one track etc. We don’t have the correct tools or know how to fix it.